TLKR T50
Owner’s Manual
English
*68015000922*
68015000922-A(EN)
U01UT071ZZZ
Printed in China
TLKR T50 Owner’s Manual
EN
Product Safety and RF Exposure for Portable
Two-Way Radios
Before using this product, read the operating
!
instructions for safe usage contained in the Product
Safety and RF Exposure booklet enclosed with
Caution
your radio.
ATTENTION!
Before using this product, read the RF energy awareness
information and operating instructions in the Product Safety and
RF Exposure booklet to ensure compliance with RF energy
exposure limits.
Package Contents
•
TLKR T50 Radio* (2 units)
•
Belt Clip (2 units)
•
AC Adapter (1 unit)
•
Rechargeable NiMH battery pack (2 units)
•
TLKR T50 Owner’s Manual
Radio Controls
Antenna
Volume/
Channel Button
Menu/Power
PTT Button
button
Call Button
Select/Lock
Monitor Button
button
Microphone
Speaker
DC in 9V Jack
Display
1. Dual Watch Indicator
2. Transmit/Receive Indicator
1
6
3. Channel Indicator
7
4. Volume Level Indicator
2
5. VOX/Room Monitor
8
Indicator
3
9
6. Scan Indicator
10
7. Battery Level Meter
4
11
8. Sub-code Indicator
9. Up timer Indicator
5
12
10.APO (Auto Power Off)
Indicator
11.Keypad Lock Indicator
12.Call Time Indicator
Preparing Your Radio
Installing the Battery
1. Make sure your radio is OFF.
2. To remove the battery compartment door, by pressing the tab at
the bottom of the compartment door. Remove the door.
3. Insert NiMH battery pack or 4 AAA batteries into the battery
compartment.
4. Replace the battery compartment door.
Battery Level and Low Battery Alert
Indicates that the battery is fully charged.
Blinks when battery is low; charge the radio or replace batteries
immediately.
Charging the Radio
1. Make sure your radio is OFF.
2. Plug the AC adapter into the DC in 9V Jack.
3. Charge battery for 16 hours.
Basic Radio Operations
Read this reference guide completely before attempting to operate
the unit.
Turning Your Radio On/Off
Press and hold the MENU/
button to turn your radio ON/OFF.
Adjusting the Volume
Adjust the volume by pressing the
and
buttons.
Adjusting the Sound (Key Beeps)
Your radio emits a beep each time one of the buttons is pressed
(except the PTT and
button).
Press and hold the button while turning the radio ON to switch the
sound ON/OFF.
Selecting a Channel and a Sub-code
In order to speak to someone, both your radios must be set to the
same channel and sub-code.
To select a channel:
1. SEL/
button to enter Select Menu. Advance until the Channel
Indicator blinks.
2.
or
to the required channel.
To select a sub-code:
1. SEL/
button to enter Select Menu. Advance until the
Sub-code Indicator blinks.
2.
or
to the required sub-code.
3. Exit the Select Menu.
Talking on Your Radio
1. Hold your radio 5–8 cm from your mouth.
2. Press and hold the PTT button while speaking. The
appears on the display.
3. Release the PTT button. You can now receive incoming calls.
When you do, the
appears on the display. To respond, repeat
procedure from step 1.
Note: When you continue to transmit for 60 seconds, the
radio emits TX Time Out tone and the
icon flashes.
The radio will stop transmitting.
Navigating through the Menu
Your radio has two menu functions : Mode Menu and Select Menu.
1. To enter the Mode Menu, press the MENU/
button.
2. To enter the Select Menu, press the SEL/
button.
3. Additional presses of the MENU/
button or the SEL/
button
will advance you through the Menu.
4. To exit the Menu function, do one of the following:
a. Press and hold the MENU/
button.
b. Press and hold the PTT, MON or the
button.
c. Wait 10 seconds until the unit automatically returns to
«Normal» mode.
Features on Your Radio
Voice Operated Transmission (VOX)
Transmission is initiated by speaking into the microphone of the
radio or the headset (headset is not included) instead of pushing
the PTT button.
To select the VOX level:
1. SEL/
button to enter Select Menu. Advance until
blinks.
2.
or
to the desired VOX sensitivity level.
3. Exit the Select Menu.
Note: Level oF (OFF) disables VOX. Levels 1-5 set the
sensitivity of the VOX circuit. Use level 1 in quiet
environments, and use level 5 in very noisy
environments. You can find the appropriate sensitivity
level by speaking into the microphone. If the
flashes, your voice is accepted.
Call Tone
Your radio is equipped with 5 selectable call tones.
To select a call tone:
1. SEL/
button to enter Select Menu. Advance until
blinks.
2.
or
to the desired call tone.
3. Exit the Select Menu.
To transmit a call tone, press the
button.
Press the PTT button to cancel the call tone.
Auto Power Off
Auto Power Off feature allows you to set the time that the radio
turns off automatically.
1. SEL/
button to enter Select Menu. Advance until
and the
current Auto Power Off time blinks.
2.
or
to select the time from oF (Off), 60, 120 or 180 minutes.
3. Exit the Select Menu.
Channel Scan Mode
Enables your radio to scan for active channels. When activity is
detected, your radio lands (stays) on that channel (for 2 seconds).
To transmit on that channel, press the PTT button. When activity
on the landed channel ends, your radio continues scanning other
channels.
To turn the channel scan ON:
1. MENU/
to enter Mode Menu. Advance until
blinks.
2. SEL/
to turn ON channel scan.
3. MENU/ ,
or PTT to turn OFF Scan mode.
Dual Watch Mode
Enables your to scan the current channel and another channel
alternately.
To set another channel and start Dual Watch:
1. MENU/
to enter Mode Menu. Advance until
blinks.
2.
or
to select the channel, then press SEL/ .
3.
or
to select the Sub-code, then press SEL/ .
4. The radio starts to Dual Watch.
Note: If you set the same channel and Sub-code as the
current channel, Dual Watch doesn’t work.
5. MENU/
to turn the Dual Watch mode OFF.
Room Monitor
Enables your radio to detect voice/noises (according to the
sensitivity level set) and transmit back to the listening radio without
pushing the PTT button. The monitoring radio is not able to
receive any transmissions in this mode.
To turn Room Monitor ON:
1. MENU/
to enter Mode Menu. Advance until
blinks.
2.
or
to the desired room monitor sensitivity level.
Note: Use level 1 in quiet environments. Use level 5 in very
noisy environments.
3. SEL/
to turn ON room monitor.
MENU/
to turn OFF Room Monitor.
Note: When the voice/noise in the monitored room continues
for more than 60 seconds, the monitoring radio stop
monitoring for 5 seconds, and resumes.
Up Timer
Enables your radio to time up to 39 minutes 59 seconds. You can
receive incoming calls in this mode.
To use up timer:
1. MENU/
to enter Mode Menu. Advance until
blinks.
2. SEL/
to select the Up Timer.
3.
to start the Up Timer
4. MENU/ ,
, MON or PTT to stop or reset up timer.
Key Lock
Press and hold SEL/
until
/ «LOCK» appears to lock the keypad.
Press and hold SEL/
until
/ «UNLK» disappears to unlock the
keypad.
LCD Backlight
The LCD display will automatically illuminate for 10 seconds after
any button is pressed (except for PTT).
Monitor Mode
Enables you to listen for weak signals on the current channel.
To turn the Monitor Mode ON:
1. Press the MON button for brief listening. The
icon blinks.
2. Press and hold the MON button for 2 seconds for continuous
listening. The
icon continues to blink.
To turn the Monitor Mode OFF:
Press the MON button to return to «Normal» mode. The
icon
stops blinking.
Roger Beep
Sounds to indicate the end of a PTT or VOX transmission. It can
be heard through the speaker when Key Beep is on. It cannot be
heard through the speaker if Key Beep is turned off.
Press and hold the
button while turning the radio ON to turn the
Roger Beep ON. Repeat the step to turn Roger Beep OFF.
Automatic Power Save
For better battery life, your radio is designed to switch to Power
Save mode when there has been no transmissions after 3
seconds. The radio can receive transmissions in this mode.
Specifications
Channels
8 PMR
Sub-code
121 (38 CTCSS and 83 DCS codes)
Frequency
446.00625 — 446.09375 MHz
Power Source NiMH Battery Pack
4 AAA Alkaline Batteries
Range
Up to 8km*
Battery Life
16 Hours (under typical use conditions)
*Range may vary depending on environmental and/or
topographical conditions.
Frequency Chart
Channel
Freq. (MHz)
Channel
Freq. (MHz)
1
446.00625
5
446.05625
2
446.01875
6
446.06875
3
446.03125
7
446.08125
4
446.04375
8
446.09375
Warranty Information
The authorized Motorola dealer or retailer where you purchased your Motorola
two-way radio and/or original accessories will honour a warranty claim and/or
provide warranty service.
Please return your radio to your dealer or retailer to claim your warranty service.
Do not return your radio to Motorola.
In order to be eligible to receive warranty service, you must present your receipt of
purchase or a comparable substitute proof of purchase bearing the date of
purchase. The two-way radio should also clearly display the serial number. The
warranty will not apply if the type or serial numbers on the product have been
altered, deleted, removed, or made illegible.
What Is Not Covered By The Warranty
Defects or damage resulting from use of the Product in other than its normal and
customary manner or by not following the instructions in this user manual.
Defects or damage from misuse, accident or neglect.
Defects of damage from improper testing, operation, maintenance, adjustment, or
any alteration or modification of any kind.
Breakage or damage to aerials unless caused directly by defects in material or
workmanship.
Products disassembled or repaired in such a manner as to adversely affect
performance or prevent adequate inspection and testing to verify any warranty
claim.
Defects or damage due to range.
Defects or damage due to moisture, liquid or spills.
All plastic surfaces and all other externally exposed parts that are scratched or
damaged due to normal use.
Products rented on a temporary basis.
Periodic maintenance and repair or replacement of parts due to normal usage,
wear and tear.
Copyright Information
The Motorola products described in this manual may include copyrighted
Motorola computer programs stored in semiconductor memories or other media.
Laws in the United States and other countries preserve for Motorola certain
exclusive rights for copyrighted computer programs including, but not limited to,
the exclusive right to copy or reproduce in any form the copyrighted computer
program. Accordingly, any copyrighted Motorola computer programs contained in
the Motorola products described in this manual may not be copied, reproduced,
modified, reverse-engineered, or distributed in any manner without the express
written permission of Motorola. Furthermore, the purchase of Motorola products
shall not be deemed to grant either directly or by implication, estoppel, or
otherwise, any license under the copyrights, patents or patent applications of
Motorola, except for the normal non-exclusive license to use that arises by
operation of law in the sale of a product.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized
M logo are trademarks or registered trademarks of Motorola
Trademark Holdings, LLC and are used under license. All other
trademarks are the property of their respective owners.
© 2012 Motorola Solutions, Inc. All rights reserved.
Как использовать наш сайт инструкций OnlineManuals.ru
Наша цель состоит в том, чтобы предоставить вам быстрый доступ к содержанию инструкции для Руководство пользователя, руководство по эксплуатации радиостанции Motorola TLKR T50.
С помощью онлайн просмотра, Вы можете быстро просмотреть содержимое инструкции и найти решение проблемы с Руководство пользователя, руководство по эксплуатации радиостанции Motorola TLKR T50.
Для Вашего удобства
Если листать руководство пользователя Руководство пользователя, руководство по эксплуатации радиостанции Motorola TLKR T50 прямо на сайте, не очень удобно для Вас, есть два возможных решения:
• Просмотр в полноэкранном режиме — легко просмотреть руководство пользователя (без загрузки его на свой компьютер), Вы можете использовать режим полноэкранного просмотра.
Для просмотра инструкции пользователя Руководство пользователя, руководство по эксплуатации радиостанции Motorola TLKR T50 на полном экране, используйте кнопку «Открыть в Pdf-viewer».
• Загрузка на компьютер — Вы можете также скачать Руководство пользователя, руководство по эксплуатации радиостанции Motorola TLKR T50 на свой компьютер и сохранить его в файлах.
Многие люди предпочитают читать документы не на экране, а в печатной версии.
Возможность печати руководства пользователя также была предусмотрена на нашем сайте,
и вы можете использовать ее, нажав на иконку «печать» в Pdf-viewer.
Нет необходимости печатать все руководство Руководство пользователя, руководство по эксплуатации радиостанции Motorola TLKR T50, можно выбрать только нужные страницы инструкции.
TLKR T50
Owner’s Manual
English
*68015000922*
68015000922-A(EN)
U01UT071ZZZ
Printed in China
TLKR T50 Owner’s Manual
EN
Product Safety and RF Exposure for Portable
Two-Way Radios
Before using this product, read the operating
!
instructions for safe usage contained in the Product
Safety and RF Exposure booklet enclosed with
Caution
your radio.
ATTENTION!
Before using this product, read the RF energy awareness
information and operating instructions in the Product Safety and
RF Exposure booklet to ensure compliance with RF energy
exposure limits.
Package Contents
•
TLKR T50 Radio* (2 units)
•
Belt Clip (2 units)
•
AC Adapter (1 unit)
•
Rechargeable NiMH battery pack (2 units)
•
TLKR T50 Owner’s Manual
Radio Controls
Antenna
Volume/
Channel Button
Menu/Power
PTT Button
button
Call Button
Select/Lock
Monitor Button
button
Microphone
Speaker
DC in 9V Jack
Display
1. Dual Watch Indicator
2. Transmit/Receive Indicator
1
6
3. Channel Indicator
7
4. Volume Level Indicator
2
5. VOX/Room Monitor
8
Indicator
3
9
6. Scan Indicator
10
7. Battery Level Meter
4
11
8. Sub-code Indicator
9. Up timer Indicator
5
12
10.APO (Auto Power Off)
Indicator
11.Keypad Lock Indicator
12.Call Time Indicator
Preparing Your Radio
Installing the Battery
1. Make sure your radio is OFF.
2. To remove the battery compartment door, by pressing the tab at
the bottom of the compartment door. Remove the door.
3. Insert NiMH battery pack or 4 AAA batteries into the battery
compartment.
4. Replace the battery compartment door.
Battery Level and Low Battery Alert
Indicates that the battery is fully charged.
Blinks when battery is low; charge the radio or replace batteries
immediately.
Charging the Radio
1. Make sure your radio is OFF.
2. Plug the AC adapter into the DC in 9V Jack.
3. Charge battery for 16 hours.
Basic Radio Operations
Read this reference guide completely before attempting to operate
the unit.
Turning Your Radio On/Off
Press and hold the MENU/
button to turn your radio ON/OFF.
Adjusting the Volume
Adjust the volume by pressing the
and
buttons.
Adjusting the Sound (Key Beeps)
Your radio emits a beep each time one of the buttons is pressed
(except the PTT and
button).
Press and hold the button while turning the radio ON to switch the
sound ON/OFF.
Selecting a Channel and a Sub-code
In order to speak to someone, both your radios must be set to the
same channel and sub-code.
To select a channel:
1. SEL/
button to enter Select Menu. Advance until the Channel
Indicator blinks.
2.
or
to the required channel.
To select a sub-code:
1. SEL/
button to enter Select Menu. Advance until the
Sub-code Indicator blinks.
2.
or
to the required sub-code.
3. Exit the Select Menu.
Talking on Your Radio
1. Hold your radio 5–8 cm from your mouth.
2. Press and hold the PTT button while speaking. The
appears on the display.
3. Release the PTT button. You can now receive incoming calls.
When you do, the
appears on the display. To respond, repeat
procedure from step 1.
Note: When you continue to transmit for 60 seconds, the
radio emits TX Time Out tone and the
icon flashes.
The radio will stop transmitting.
Navigating through the Menu
Your radio has two menu functions : Mode Menu and Select Menu.
1. To enter the Mode Menu, press the MENU/
button.
2. To enter the Select Menu, press the SEL/
button.
3. Additional presses of the MENU/
button or the SEL/
button
will advance you through the Menu.
4. To exit the Menu function, do one of the following:
a. Press and hold the MENU/
button.
b. Press and hold the PTT, MON or the
button.
c. Wait 10 seconds until the unit automatically returns to
«Normal» mode.
Features on Your Radio
Voice Operated Transmission (VOX)
Transmission is initiated by speaking into the microphone of the
radio or the headset (headset is not included) instead of pushing
the PTT button.
To select the VOX level:
1. SEL/
button to enter Select Menu. Advance until
blinks.
2.
or
to the desired VOX sensitivity level.
3. Exit the Select Menu.
Note: Level oF (OFF) disables VOX. Levels 1-5 set the
sensitivity of the VOX circuit. Use level 1 in quiet
environments, and use level 5 in very noisy
environments. You can find the appropriate sensitivity
level by speaking into the microphone. If the
flashes, your voice is accepted.
Call Tone
Your radio is equipped with 5 selectable call tones.
To select a call tone:
1. SEL/
button to enter Select Menu. Advance until
blinks.
2.
or
to the desired call tone.
3. Exit the Select Menu.
To transmit a call tone, press the
button.
Press the PTT button to cancel the call tone.
Auto Power Off
Auto Power Off feature allows you to set the time that the radio
turns off automatically.
1. SEL/
button to enter Select Menu. Advance until
and the
current Auto Power Off time blinks.
2.
or
to select the time from oF (Off), 60, 120 or 180 minutes.
3. Exit the Select Menu.
Channel Scan Mode
Enables your radio to scan for active channels. When activity is
detected, your radio lands (stays) on that channel (for 2 seconds).
To transmit on that channel, press the PTT button. When activity
on the landed channel ends, your radio continues scanning other
channels.
To turn the channel scan ON:
1. MENU/
to enter Mode Menu. Advance until
blinks.
2. SEL/
to turn ON channel scan.
3. MENU/ ,
or PTT to turn OFF Scan mode.
Dual Watch Mode
Enables your to scan the current channel and another channel
alternately.
To set another channel and start Dual Watch:
1. MENU/
to enter Mode Menu. Advance until
blinks.
2.
or
to select the channel, then press SEL/ .
3.
or
to select the Sub-code, then press SEL/ .
4. The radio starts to Dual Watch.
Note: If you set the same channel and Sub-code as the
current channel, Dual Watch doesn’t work.
5. MENU/
to turn the Dual Watch mode OFF.
Room Monitor
Enables your radio to detect voice/noises (according to the
sensitivity level set) and transmit back to the listening radio without
pushing the PTT button. The monitoring radio is not able to
receive any transmissions in this mode.
To turn Room Monitor ON:
1. MENU/
to enter Mode Menu. Advance until
blinks.
2.
or
to the desired room monitor sensitivity level.
Note: Use level 1 in quiet environments. Use level 5 in very
noisy environments.
3. SEL/
to turn ON room monitor.
MENU/
to turn OFF Room Monitor.
Note: When the voice/noise in the monitored room continues
for more than 60 seconds, the monitoring radio stop
monitoring for 5 seconds, and resumes.
Up Timer
Enables your radio to time up to 39 minutes 59 seconds. You can
receive incoming calls in this mode.
To use up timer:
1. MENU/
to enter Mode Menu. Advance until
blinks.
2. SEL/
to select the Up Timer.
3.
to start the Up Timer
4. MENU/ ,
, MON or PTT to stop or reset up timer.
Key Lock
Press and hold SEL/
until
/ «LOCK» appears to lock the keypad.
Press and hold SEL/
until
/ «UNLK» disappears to unlock the
keypad.
LCD Backlight
The LCD display will automatically illuminate for 10 seconds after
any button is pressed (except for PTT).
Monitor Mode
Enables you to listen for weak signals on the current channel.
To turn the Monitor Mode ON:
1. Press the MON button for brief listening. The
icon blinks.
2. Press and hold the MON button for 2 seconds for continuous
listening. The
icon continues to blink.
To turn the Monitor Mode OFF:
Press the MON button to return to «Normal» mode. The
icon
stops blinking.
Roger Beep
Sounds to indicate the end of a PTT or VOX transmission. It can
be heard through the speaker when Key Beep is on. It cannot be
heard through the speaker if Key Beep is turned off.
Press and hold the
button while turning the radio ON to turn the
Roger Beep ON. Repeat the step to turn Roger Beep OFF.
Automatic Power Save
For better battery life, your radio is designed to switch to Power
Save mode when there has been no transmissions after 3
seconds. The radio can receive transmissions in this mode.
Specifications
Channels
8 PMR
Sub-code
121 (38 CTCSS and 83 DCS codes)
Frequency
446.00625 — 446.09375 MHz
Power Source NiMH Battery Pack
4 AAA Alkaline Batteries
Range
Up to 8km*
Battery Life
16 Hours (under typical use conditions)
*Range may vary depending on environmental and/or
topographical conditions.
Frequency Chart
Channel
Freq. (MHz)
Channel
Freq. (MHz)
1
446.00625
5
446.05625
2
446.01875
6
446.06875
3
446.03125
7
446.08125
4
446.04375
8
446.09375
Warranty Information
The authorized Motorola dealer or retailer where you purchased your Motorola
two-way radio and/or original accessories will honour a warranty claim and/or
provide warranty service.
Please return your radio to your dealer or retailer to claim your warranty service.
Do not return your radio to Motorola.
In order to be eligible to receive warranty service, you must present your receipt of
purchase or a comparable substitute proof of purchase bearing the date of
purchase. The two-way radio should also clearly display the serial number. The
warranty will not apply if the type or serial numbers on the product have been
altered, deleted, removed, or made illegible.
What Is Not Covered By The Warranty
Defects or damage resulting from use of the Product in other than its normal and
customary manner or by not following the instructions in this user manual.
Defects or damage from misuse, accident or neglect.
Defects of damage from improper testing, operation, maintenance, adjustment, or
any alteration or modification of any kind.
Breakage or damage to aerials unless caused directly by defects in material or
workmanship.
Products disassembled or repaired in such a manner as to adversely affect
performance or prevent adequate inspection and testing to verify any warranty
claim.
Defects or damage due to range.
Defects or damage due to moisture, liquid or spills.
All plastic surfaces and all other externally exposed parts that are scratched or
damaged due to normal use.
Products rented on a temporary basis.
Periodic maintenance and repair or replacement of parts due to normal usage,
wear and tear.
Copyright Information
The Motorola products described in this manual may include copyrighted
Motorola computer programs stored in semiconductor memories or other media.
Laws in the United States and other countries preserve for Motorola certain
exclusive rights for copyrighted computer programs including, but not limited to,
the exclusive right to copy or reproduce in any form the copyrighted computer
program. Accordingly, any copyrighted Motorola computer programs contained in
the Motorola products described in this manual may not be copied, reproduced,
modified, reverse-engineered, or distributed in any manner without the express
written permission of Motorola. Furthermore, the purchase of Motorola products
shall not be deemed to grant either directly or by implication, estoppel, or
otherwise, any license under the copyrights, patents or patent applications of
Motorola, except for the normal non-exclusive license to use that arises by
operation of law in the sale of a product.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized
M logo are trademarks or registered trademarks of Motorola
Trademark Holdings, LLC and are used under license. All other
trademarks are the property of their respective owners.
© 2012 Motorola Solutions, Inc. All rights reserved.
Просмотр
Доступно к просмотру 14 страниц. Рекомендуем вам скачать файл инструкции, поскольку онлайн просмотр документа может сильно отличаться от оригинала.
-
The authorized Motorola dealer or retailer where you purchased your Motorola two-way radio and/or original accessories will honour a warranty claim and/or Please return your radio to your dealer or retailer to claim your warranty service. In order to be eligible to receive warranty service, you must present your receipt of purchase or a comparable substitute proof of purchase bearing the date of purchase. The two-way radio should also clearly display the seria Warranty Information provide warranty service. Do not return your radio to Motorola. altered, deleted, removed, or made illegible. What Is Not Covered By The Warranty Defects or damage from misuse, accident or neglect. any alteration or modification of any kind. workmanship. claim. Defects or damage due to range. Defects or damage due to moisture, liquid or spills. damaged due to normal use. Products rented on a temporary basis. wear and tear. icon Copyrig Enables your radio to time up to 39 minutes 59 seconds. You can blinks. to enter Mode Menu. Advance until to select the Up Timer. , MON or PTT to stop or reset up timer. / ”LOCK” appears to lock the keypad. until / ”UNLK” disappears to unlock the until The LCD display will automatically illuminate for 10 seconds after any button is pressed (except for PTT). Enables you to listen for weak signals on the current channel. icon blinks. 1. Press the MO Up Timer receive incoming calls in this mode. button. To use up timer: button. 1. MENU/ button 2. SEL/ to start the Up Timer 3. , 4. MENU/ button. Key Lock Press and hold SEL/ Press and hold SEL/ keypad. LCD Backlight blinks. Monitor Mode To turn the Monitor Mode ON: listening. The To turn the Monitor Mode OFF: stops blinking. Roger Beep blinks. Press and hold the Automatic Power Save and the blinks. Specifications Chan Navigating through the Menu Your radio has two menu functions : Mode Menu and Select Menu. 1. To enter the Mode Menu, press the MENU/ 2. To enter the Select Menu, press the SEL/ button or the SEL/ 3. Additional presses of the MENU/ will advance you through the Menu. 4. To exit the Menu function, do one of the following: button. a. Press and hold the MENU/ b. Press and hold the PTT, MON or the c. Wait 10 seconds until the unit automatically returns to “Normal” 1. Dual Watch Indicator 2. Transmit/Receive Indicator 3. Channel Indicator 4. Volume Level Indicator 5. VOX/Room Monitor Indicator 6. Scan Indicator 7. Battery Level Meter 8. Sub-code Indicator 9. Up timer Indicator 10.APO (Auto Power Off) Indicator 11.Keypad Lock Indicator 12.Call Time Indicator Blinks when battery is low; charge the radio or replace batteries button to turn your radio ON/OFF. buttons. appears on the display. To respond, repeat 6 7 8 9 10 11 12 2. To remove the battery compartment door, by pressing the tab at the bottom of the compartment door. Remove the door. 3. Insert NiMH battery pack or 4 AAA batteries into the battery Indicates that the battery is fully charged. 2. Plug the AC adapter into the DC in 9V Jack. Read this reference guide completely before attempting to operate and Your radio emits a beep each time one of the buttons is pressed button). Press and hol Preparing Your Radio Installing the Battery 1. Make sure your radio is OFF. 4. Replace the battery compartment door. Battery Level and Low Battery Alert immediately. Charging the Radio 1. Make sure your radio is OFF. 3. Charge battery for 16 hours. Basic Radio Operations Turning Your Radio On/Off Press and hold the MENU/ Adjusting the Volume Adjust the volume by pressing the Adjusting the Sound (Key Beeps) (except the PTT and Selec Display 1 2 3 4 5 compartment. the unit. sound ON/OFF. 1. SEL/ or 2. 1. SEL/ or 2. TLKR T50 Owner’s Manual English EN Product Safety and RF Exposure for Portable Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet to ensure compliance with RF energy Antenna Menu/Power button Select/Lock *68015000922* 68015000922-A(EN) U01UT071ZZZ Printed in China TLKR T50 Owner’s Manual Two-Way Radios ! your radio. Caution ATTENTION! exposure limits. Package Contents TLKR T50 Radio* (2 units) • Belt Clip (2 units) • AC Adapter (1 unit) • Rechargeable NiMH battery pack (2 units) • TLKR T50 Owner's Manual • Radio Controls Volume/ Channel Button PTT Button Call Button Monitor Button Speaker DC in 9V Jack
-
Der autorisierte Motorola Handler oder Vertriebspartner, bei dem Sie Ihr Motorola Sprechfunkgerat und/oder das Originalzubehor gekauft haben, nimmt Garantiean- spruche entgegen und/oder bietet die entsprechenden Garantieleistungen. Bringen Sie bitte Ihr Sprechfunkgerat zu Ihrem Motorola Handler oder Vertriebs- partner, um Ihre Garantieleistungen in Anspruch zu nehmen. Senden Sie das Damit Sie die Garantieleistungen in Anspruch nehmen konnen, mussen Sie den Kaufb Garantieinformationen Sprechfunkgerat nicht zum Hersteller Motorola ein. gemacht wurden. Garantieausschluss sind. zuruckzufuhren sind. oder Verarbeitungsfehler zuruckzufuhren ist. des Garantieanspruches unmoglich machen. Defekte oder Schaden aufgrund der Reichweite. von Flussigkeiten. Nutzung zerkratzt oder beschadigt sind. Urheberrechtshinweise Produkts ergeben. jeweiligen Inhaber. Ermoglicht es dem Funkgerat, bis zu 39 Minuten und 59 Sekunden zu stoppen. In diesem Modus konnen Sie eingehende Anrufe empfangen. , um „Modusmenu“ aufzurufen. Fahren blinkt. zum Auswahlen des Up-Timers. , MON oder PTT zum Anhalten oder Zurucksetzen des / „SPERREN“ angezeigt wird, um das gedruckt, bis / „ENTSPERREN“ nicht mehr angezeigt gedruckt, bis Das LCD-Display wird automatisch 10 Sekunden lang beleuchtet, nachdem eine beliebige Taste gedruckt wu Up-Timer So verwenden Sie den Up-Timer: . 1. Drucken Sie die Taste MENU/ . Sie so lange fort, bis bewegen Sie SEL/ 2. zum Starten des Up-Timers. 3. , Menu/ 4. Up-Timers. Tastensperre Halten Sie SEL/ Tastenfeld zu sperren. Halten Sie SEL/ wird, um das Tastenfeld zu entsperren. LCD-Hintergrundbeleuchtung Monitormodus achten. So schalten Sie den Monitormodus EIN: wird angezeigt. 2. abzuhoren. Das So schalten Sie den Monitormodus AUS: -Symbol h Navigieren durch das Menu Das Funkgerat verfugt uber zwei Menufunktionen: „Modusmenu“ und „Menuauswahl“. 1. Drucken Sie zum Aufrufen von „Modusmenu“ die Taste MENU/ 2. Drucken Sie zum Aufrufen von „Menuauswahl“ die Taste SEL/ oder SEL/ 3. Durch weiteres Betatigen der Taste MENU/ sich im Menu fort. 4. Um die Menufunktion zu verlassen, fuhren Sie einen der folgenden Schritte aus: gedruckt. a. Halten Sie die Taste MENU/ gedruckt. b. Halten Sie die Taste PTT, 1. Dual Watch-Anzeige 2. Empfang-/Sendeanzeige 3. Kanalanzeige 4. Lautstarkeanzeige 5. VOX/Raummonitor- Anzeige 6. Suchanzeige 7. Akkustandanzeige 8. Subcodeanzeige 9. Up-Timer-Anzeige 10.Automatische Abschaltungsanzeige (APO) 11.Tastatursperranzeige 12.Anrufszeitanzeige gedruckt, um das Funkgerat an. und -Taste). zum Offnen von „Menuauswahl“. Fahren Sie fort, zum Offnen von „Menuauswahl“. Fahren Sie fort, auf dem Vorbereiten des Funkgerats Aufladen des Funkgerats 3. Laden Sie den Akku 16 Stunden lang auf. Ein-/Ausschalten des Funkgerats Halten Sie die Taste MENU/ ein- oder auszuschalten. Anpassen der Lautstarke Anpassen des Tons (Tastentone) gedruckt wird (mit Ausnahme der PTT- und der Dadurch wird der Ton ein- bzw. ausgeschaltet. So wahlen Sie einen Kanal aus: bis die Kanalanzeige blinkt. So wahlen Sie einen Subcode aus: bis die Subcodeanzeig 6 7 8 9 10 11 12 1. Vergewissern Sie sich, dass das Funkgerat ausgeschaltet ist. 2. Drucken Sie zum Entfernen der Klappe des Batteriefachs auf die Lasche unten am Batteriefach. Nehmen Sie die Abdeckung 3. Legen Sie NiMH-Akkus oder 4 AAA-Batterien in das 4. Bringen Sie die Klappe des Batteriefachs wieder an. Akkustandanzeige und Hinweis auf leere Batterien Zeigt an, dass der Akku vollstandig geladen ist. Blinkt, wenn Akku fast leer ist; Laden Sie das F Display 1 2 3 4 5 Einlegen des Akkus vom Gerat. Batteriefach ein. in Betrieb nehmen. 1. Taste SEL/ oder 2. 1. Taste SEL/ oder 2. Das Symbol Benutzerhandbuch fur TLKR T50 DE Produktsicherheit und Funkfrequenzstrahlung Bitte lesen Sie die im Heft uber Produktsicherheit und Funkfrequenzstrahlung enthaltenen Hinweise fur den sicheren Einsatz des Funkgerats, bevor Sie es in Betrieb nehmen. Das Heft erhalten Sie Vorsichtsinformationen und die Bedienungsanweisungen im Heft Antenne Menu- und Ein/Aus-Taste Auswahl- und Sperrtaste Mikrofon *68015000922* 68015000922-A(DE) U01UT071ZZZ Benutzerhandbuch fur TLKR T50 fur tragbare Zweiwegefunkgerate ! Vorsicht zusammen mit Ihrem Funkgerat. ACHTUNG! Lesen Sie vor Verwendung des Produkts die HF-Energie- uber Produktsicherheit und Funkfrequenzstrahlung, um die Einhaltung der HF-Energiegrenzwerte zu gewahrleisten. Packungsinhalt TLKR T50-Funkgerat* (2 Einheiten) • Gurtelclip (2 Einheiten) • AC-Adapter (1 Einheit) • Au Deutsch
-
Le revendeur ou le detaillant agree Motorola aupres duquel vous avez achete votre radio bidirectionnelle Motorola et/ou les accessoires agrees s'engage a accepter les demandes de garantie et/ou propose un service de garantie. Retournez votre radio a votre revendeur ou detaillant pour beneficier du service Pour pouvoir beneficier du service de garantie, vous devez presenter votre justificatif d'achat ou tout document similaire sur lequel figure la date d'achat. Informations de garantie de garantie. Ne retournez pas la radio a Motorola. efface, supprime ou est illisible. Elements non couverts par la garantie d'utilisation. / VERR negligence. / sorte que ce soit. soumettre une demande de garantie. Tout defaut ou dommage lie a la portee. clignote. suite a l'utilisation normale de la radio. Les produits loues de maniere temporaire. Informations concernant le Copyright qui decoule legalement de la vente du produ Permet a votre radio de programmer jusqu'a 39 minutes et 59 secondes. Vous pouvez recevoir des appels entrants dans ce mode. Pour utiliser le programmateur, procedez comme suit : pour acceder au menu. Parcourez le menu clignote. pour selectionner le programmateur. pour lancer le programmateur. , SURV ou sur le bouton PTT pour stopper ou , jusqu'a ce que jusqu'a ce que Appuyez de facon prolongee sur le bouton SEL/ L'ecran LCD s'allume automatiquement Programmateur . 1. Appuyez sur MENU/ . jusqu'a ce que l'icone pour parcourir Appuyez sur SEL/ 2. Appuyez sur 3. Appuyez sur MENU/ 4. . reinitialiser le programmateur. . Verrouillage des touches Appuyez de facon prolongee sur le bouton SEL/ s'affiche pour verrouiller le clavier. DEVERR s'affiche pour deverrouiller le clavier. Retroeclairage de l'ecran LCD Mode Surveillance 2. SURV pendant 2 secondes. L'icone cesse de clignoter. clignote, cela To Navigation dans le menu Vos radios disposent de deux menus : le menu de selection et le menu courant. 1. Pour acceder au menu courant, appuyez sur le bouton MENU/ 2. Pour acceder au menu de selection, appuyez sur le bouton SEL/ ou SEL/ 3. Appuyez plusieurs fois sur le bouton MENU/ le menu. 4. Pour quitter le menu, effectuez l'une des operations suivantes : a. Appuyez de facon prolongee sur le bouton MENU/ b. Appuyez de facon prolongee sur le bouton PTT, SURV ou 1. Indicateur de la fonction de double veille Indicateur de transmission/ reception Indicateur du canal Indicateur du niveau de volume Indicateur du systeme de surveillance de l'environnement/VOX Indicateur de lecture Niveau de la batterie Indicateur de sous-code Indicateur du programmateur 10.Indicateur de la fonction d'arret automatique 11.Indicateur de verrouillage du clavier 12.Indicateur de la duree d'appel pour allumer/eteindre . et po Preparation de votre radio Installation de la batterie 1. Assurez-vous que la radio est ETEINTE. languette situee en bas. Retirez le couvercle. 4. Replacez le couvercle du compartiment. Chargement de la radio 1. Assurez-vous que la radio est ETEINTE. 2. Branchez l'adaptateur secteur a la prise CC 9 V. Chargez la batterie pendant 16 heures. Fonctionnement de base Mise sous/hors tension de la radio Appuyez de facon prolongee sur le bouton 6 2. 7 3. 4. 8 5. 9 10 11 6. 7. 12 8. 9. 2. Pour retirer le couvercle du compartiment a piles, appuyez sur la 3. Inserez la batterie NiMH ou 4 piles de type AAA dans le compartiment Niveau de la batterie et alerte de batterie faible Indique que la batterie est chargee. Clignote lorsque la batterie est faible. Chargez la radio ou remplacez la batterie immediatement. Lisez le present guide de reference dans son integralite avant d'utiliser la Ecran 1 2 3 4 5 prevu a cet effet. 3. radio. la radio. 2. Les touches 2. Appuyez sur L'icone FR Guide d'utilisation de la radio TLKR Avant d'utiliser ce produit, vous devez lire les instructions de securite presentees dans le livret joint concernant la securite des equipements et Avant d'utiliser ce produit, vous devez lire les informations sur les frequences radioelectriques et les instructions d'utilisation du livret Securite des equipements et exposition aux frequences radio pour Antenne Bouton Menu/ Marche/arret Bouton de selecti *68015000922* 68015000922-A(FR) U01UT071ZAZ Printed in China Guide d'utilisation de la radio TLKR T50 Securite des equipements et exposition aux frequences radio pour les radios portables bidirectionnelles ! l'exposition aux frequences radio. Attention ATTENTION ! connaitre et appliquer les limites d'exposition aux frequences radio. Contenu de la boite Radio TLKR T50* (2 unites) • Clip de ceinture (2 unites) • Adaptateur Francais T50
- 1
- 2
- 3
- 4
- 14
Требуется руководство для вашей Motorola TLKR T50 Уоки-токи? Ниже вы можете просмотреть и загрузить бесплатно руководство в формате PDF. Кроме того, приведены часто задаваемые вопросы, рейтинг изделия и отзывы пользователей, что позволит оптимально использовать ваше изделие. Если это не то руководство, которое вы искали, – свяжитесь с нами.
Ваше устройство неисправно, и в руководстве отсутствует решение? Перейдите в Repair Café для получения бесплатных ремонтных услуг.
Руководство
Рейтинг
Сообщите нам, что вы думаете о Motorola TLKR T50 Уоки-токи, оставив оценку продукта. Хотите поделиться вашими впечатлениями от данного изделия или задать вопрос? Вы можете оставить комментарий в нижней части страницы.
Довольны ли вы данным изделием Motorola?
Да Нет
43 голоса
