Инструкция к автомагнитоле jvc kd g747

CD RECEIVER

РЕСИВЕР С ПРОИГРЫВАТЕЛЕМ КОМПАКТ-ДИСКОВ ПРИЙМАЧ З ПРОГРАВАЧЕМ КОМПАКТ-ДИСКІВ

KD-G747

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

1.CLASS 1 LASER PRODUCT

2.CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3.CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.

4.REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

[European Union only]

Warning:

If you need to operate the unit while driving, be sure to look around carefully or you may be involved in a traffic accident.

Caution on volume setting:

Digital devices (CD/USB) produce very little noise compared with other sources. Lower the volume before playing these digital sources to avoid damaging the speakers by sudden increase of the output level.

For safety…

•Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

•Stop the car before performing any complicated operations.

Temperature inside the car…

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

How to reset your unit

• Your preset adjustments will also be erased.

How to forcibly eject a disc

“PLEASE” and “EJECT” appear alternately on the display.

•Be careful not to drop the disc when it ejects.

•If this does not work, reset your unit.

How to use the M MODE button

If you press M MODE, the unit goes into functions mode, then the number buttons and 5/∞ buttons will work as different function buttons.

Ex.: When number button 2 works as

MO (monaural) button.

Detaching the control panel

Avoid touching the connectors.

Control panel

Parts identification

Display window

Installing the lithium coin battery (CR2025)

Aim the remote controller directly at the remote sensor on the unit. Make sure there is no obstacle in between.

Warning:

•Do not install any battery other than CR2025 or its equivalent; otherwise, it may explode.

•Do not leave the remote controller in a place (such as the dashboard) exposed to direct sunlight for a long time; otherwise, it may explode.

•Store the battery in a place where children cannot reach to avoid the risk of accidents.

•To prevent the battery from over-heating, cracking, or starting a fire:

–Do not recharge, short, disassemble, heat the battery, or dispose of it in a fire.

–Do not leave the battery with other metallic materials.

–Do not poke the battery with tweezers or similar tools.

–Wrap the battery with tape and insulate when throwing away or saving it.

1(standby/on/attenuator) button

•Turns the power on if pressed briefly or attenuates the sound when the power is on.

•Turns the power off if pressed and held. 2 5 U (up) / D (down) ∞ buttons

•Changes the FM/AM bands with 5 U.

•Changes the preset stations with D ∞.

•Changes the folder of the MP3/WMA.

3VOL – / VOL + buttons

•Adjusts the volume level. 4 SOUND button

•Selects the sound mode (iEQ: intelligent

equalizer).

5SOURCE button

• Selects the source.

62 R (reverse) / F (forward) 3 buttons

•Searches for stations if pressed briefly.

•Fast-forwards or reverses the track if pressed and held.

•Changes the track if pressed briefly.

Getting started

Volume level appears.

@Adjust the sound as you want. (See page 14.)

To drop the volume in a moment (ATT)

To restore the sound, press the button again.

To turn off the power

Basic settings

•See also “General settings — PSM” on pages 15 – 17.

1

2

1Canceling the display demonstrations

Select “DEMO,” then “DEMO OFF.”

2Setting the clock

Select “CLOCK HOUR”, then adjust the hour. Select “CLOCK MIN” (minute), then adjust the minute.

Select “24H/12H,” then “24 HOUR” or “12 HOUR”.

3 Finish the procedure.

To check the current clock time while the power is turned off

Clock time is shown on the display for about 5 seconds. See also page 15.

Radio operations

~

Ÿ

Lights up when receiving an FM stereo broadcast with sufficient signal strength.

! Start searching for a station.

When a station is received, searching stops. To stop searching, press the same button again.

Note:

FM1 and FM2: 87.5 MHz – 108.0 MHz

FM3: 65.00 MHz – 74.00 MHz

To tune in to a station manually

In step ! above…

1

2 Select a desired station frequency.

When an FM stereo broadcast is hard to receive

Reception improves, but the stereo effect will be lost.

To restore the stereo effect, repeat the same procedure. “MONO OFF” appears and the MO indicator goes off.

Storing stations in memory

You can preset six stations for each band.

FM station automatic presetting— SSM (Strong-station Sequential Memory)

1Select the FM band (FM1 – FM3) you want to store into.

2

3

“SSM” flashes, then disappears when automatic presetting is over.

Local FM stations with the strongest signals are searched and stored automatically in the FM band.

Continued on the next page

Manual presetting

Ex.: Storing the FM station of 92.50MHz into preset

2

3

Preset number flashes for a while.

FM RDS operations

What you can do with RDS

RDS (Radio Data System) allows FM stations to send an additional signal along with their regular programme signals.

By receiving the RDS data, this unit can do the following:

•Programme Type (PTY) Search (see the following)

•TA (Traffic Announcement) and PTY Standby Receptions (see pages 9, 10, and 16)

•Tracing the same programme automatically —Network-Tracking Reception (see page 10)

•Programme Search (see pages 10 and 16)

Listening to a preset station

1

2Select the preset station (1 – 6) you want.

or

To check the other information while listening to an FM (non-RDS) or AM station

• For FM RDS stations, see page 10.

Frequency Ô Clock

Searching for your favorite FM RDS programme

You can tune in to a station broadcasting your favorite programme by searching for a PTY code.

• To store your favorite programme types, see page 9.

ŸSelect one of your favorite programme types.

or

Select one of the PTY codes (see page 10).

!Start searching for your favorite programme.

If there is a station broadcasting a programme of the same PTY code as you have selected, that station is tuned in.

Storing your favorite programme types

You can store six favorite programme types.

Preset programme types in the number buttons (1 to 6):

1Select a PTY code (see steps ~ to ! on pages 8 and 9).

2Select the preset number (1 – 6) you want to store into.

Using the standby receptions

TA Standby Reception

TA Standby Reception allows the unit to switch temporarily to Traffic Announcement (TA) from any source other than AM.

The volume changes to the preset TA volume level if the current level is lower than the preset level (see

page 16).

To activate TA Standby Reception

The TP (Traffic Programme) indicator either lights up or flashes.

•If the TP indicator lights up, TA Standby Reception is activated.

•If the TP indicator flashes, TA Standby Reception is not yet activated. (This occurs when you are listening to an FM station without the RDS signals required for TA Standby Reception.)

To activate TA Standby Reception, tune in to another station providing these signals. The TP indicator will stop flashing and remain lit.

To deactivate the TA Standby Reception

The TP indicator goes off.

ROCK M MEMORY

Ex.: When “ROCK M” is selected

3Repeat steps 1 and 2 to store other PTY codes into other preset numbers.

4 Finish the procedure.

PTY Standby Reception

PTY Standby Reception allows the unit to switch temporarily to your favorite PTY programme from any source other than AM.

To activate and select your favorite PTY code for PTY Standby Reception, see page 16.

The PTY indicator either lights up or flashes.

•If the PTY indicator lights up, PTY Standby Reception is activated.

•If the PTY indicator flashes, PTY Standby Reception is not yet activated.

To activate PTY Standby Reception, tune in to another station providing these signals. The PTY indicator will stop flashing and remain lit.

Continued on the next page

To deactivate the PTY Standby Reception, select “OFF” for the PTY code (see page 16). The PTY indicator goes off.

Tracing the same programme— Network-Tracking Reception

When driving in an area where FM reception is not sufficient enough, this unit automatically tunes in to another FM RDS station of the same network, possibly broadcasting the same programme with stronger signals (see the illustration below).

When shipped from the factory, Network-Tracking Reception is activated.

To change the Network-Tracking Reception setting, see “AF-REG” on page 16.

Programme A broadcasting on different frequency areas (01 – 05)

•The unit takes some time to tune in to another station using programme search.

•See also page 16.

To check the current clock time while listening to an FM RDS station

Station name (PS) = Station Frequency = Programme type (PTY) = Clock = (back to the beginning)

PTY codes

NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, POP M (music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS, OTHER M (music), WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, JAZZ, COUNTRY, NATION M (music), OLDIES, FOLK M (music), DOCUMENT

Automatic station selection— Programme Search

Usually when you press the number buttons, the preset station is tuned in.

If the signals from the FM RDS preset station are not sufficient for good reception, this unit, using the AF data, tunes in to another frequency broadcasting the same programme as the original preset station is broadcasting.

Disc / USB device operations

: For built-in CD player operations.

: For external USB device operations.

Playing a disc in the unit

All tracks will be played repeatedly until you change the source or eject the disc.

Caution:

Make sure to detach the USB device before opening the control panel, as it might block the opening mechanism.

• To detach the USB device, see page 11.

To stop play and eject the disc

• Press SOURCE to listen to another playback source.

Playing from a USB device

This unit can play MP3/WMA tracks stored in a USB device (except HDD).

All tracks in the USB device will be played repeatedly until you change the source.

~

ŸUSB memory

USB input jack

If a USB device has been attached…

Playback starts from where it has been stopped previously.

•If a different USB device is currently attached, playback starts from the beginning.

Cautions:

•Avoid using the USB device if it might hinder your safety driving.

•Do not pull out or attach the USB device repeatedly while “READING” appears on the display.

•Do not start a car engine if a USB device is connected.

•This unit may not be able to play the files depending on the type of the USB device.

•Operation and power supply may not work as intended for some USB devices.

•You cannot connect a computer to the USB input jack of the unit.

•Make sure all important data has been backed up to avoid losing the data.

•Do not leave a USB device in the car, expose to direct sunlight, or high temperature to avoid deformation or cause damage to the USB device.

•Some USB devices may not work immediately after you turn on the power.

•For more details about USB operations, see pages 19 and 20.

Continued on the next page

To fast-forward or reverse the track

To go to the next or previous folder (for MP3/WMA)

To locate a particular track (for CD) or folder (for MP3/WMA) directly

To select a number from 01 – 06:

Other main functions

Skipping tracks quickly during play

•For MP3/WMA, you can skip tracks within the same folder.

Ex.: To select track 32 while playing tracks whose number is a single digit (1 to 9)

1

2

Each time you press the button, you can skip 10 tracks.

•After the last track, the first track will be selected and vice versa.

•To use direct folder access on MP3/WMA, it is required that folders are assigned with 2-digit numbers at the beginning of their folder names— 01, 02, 03, and so on.

To select a particular track in a folder (for MP3/WMA):

Changing the display information

While playing an audio CD or CD Text

A = B = Disc title/performer*1 = Track title*1 [ ] = (back to the beginning)

While playing an MP3/WMA disc or USB device

•When “TAG DISPLAY” is set to “TAG ON” (see page 17)

A = B = Album name/performer (folder name*2) [ ] = Track title (file name*2) [ ] = (back to the beginning)

• When “TAG DISPLAY” is set to “TAG OFF”

A = B = Folder name [ ] = File name

[ ] = (back to the beginning)

A : The elapsed playing time with the current track number

B : Clock with the current track number

[ ] : Corresponding indicator lights up on the display

*1 If the current disc is an audio CD, “NO NAME” appears. *2 If an MP3/WMA file does not have Tag information, folder name and file name appear. In this case, the

TAG indicator will not light up.

Selecting the playback modes

You can use only one of the following playback modes at a time.

1

2 Select your desired playback mode.

7 Repeat play

* Only while playing a media (MP3/WMA/USB).

[ ] : Corresponding indicator lights up on the display.

2

Adjusting the sound

You can adjust the sound characteristics to your preference.

1

2

Indication, [Range]

BASS *2, [–06 to +06]

Adjust the bass.

MIDDLE *2 (mid-range), [–06 to +06] Adjust the mid-range frequencies sound level.

TREBLE *2, [–06 to +06]

Adjust the treble.

FADER *3, [R06 to F06]

Adjust the front and rear speaker output balance.

BALANCE *4, [L06 to R06]

Adjust the left and right speaker output balance.

LOUD *5 (loudness), [LOUD ON or LOUD OFF] Boost low and high frequencies to produce a well-balanced sound at a low volume level.

SUB.W*1, [00 to 08, initial: 04]

Adjust the subwoofer output level.

VOL ADJ (volume adjust), [–05 to +05, initial: 00] Adjust the volume level of each source (except FM), in relation to the FM volume level. The volume level will automatically increase or decrease when you change the source.

•Before making an adjustment, select the source you want to adjust.

VOLUME, [00 to 50 or 00 to 30] *6

Adjust the volume.

*1 Displayed only when “L/O MODE” is set to “SUB.W” (see page 16).

*2 When you adjust the bass, mid-range, or treble, the adjustment you have made is stored for the currently selected sound mode (iEQ) including “USER.”

*3 If you are using a two-speaker system, set the fader level to “00.”

*4 This adjustment will not affect the subwoofer output. *5 The adjustment made (LOUD ON/LOUD OFF) will be

applied to all sound modes.

*6 Depending on the amplifier gain control setting. (See page 17 for details.)

General settings — PSM

You can change PSM (Preferred Setting Mode) items listed in the table below and on pages 16 and 17.

3 Adjust the PSM item selected.

More about this unit

Basic operations

Turning on the power

•By pressing SOURCE on the unit, you can also turn on the power. If the source is ready, playback also starts.

Turning off the power

•If you turn off the power while listening to a track, playback will start from where it had been stopped previously next time you turn on the power.

Tuner operations

Storing stations in memory

•During SSM search…

–All previously stored stations are erased and the stations are stored anew.

–Received stations are preset in No. 1 (lowest frequency) to No. 6 (highest frequency).

–When SSM is over, the station stored in No. 1 will be automatically tuned in.

•When storing a station manually, the previously preset station is erased when a new station is stored in the same preset number.

FM RDS operations

•Network-Tracking Reception requires two types of RDS signals—PI (Programme Identification) and AF (Alternative Frequency) to work correctly. Without receiving these data correctly, Network-Tracking Reception will not operate correctly.

•If a Traffic Announcement is received by TA Standby Reception, the volume level automatically changes to the preset level (TA VOL) if the current level is lower than the preset level.

•When Alternative Frequency Reception is activated (with AF selected), Network-Tracking Reception is also activated automatically.

•If you want to know more about RDS, visit <http://www.rds.org.uk>.

Disc operations

Caution for DualDisc playback

•The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

General

•This unit has been designed to reproduce CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA), MP3 and WMA formats.

•MP3 and WMA “tracks” (words “file” and “track” are used interchangeably) are recorded in “folders.”

•When a disc is inserted upside down, “PLEASE” and “EJECT” appear alternately on the display. Press OPEN, then 0 to eject the disc.

•While fast-forwarding or reversing on an MP3 or WMA disc, you can only hear intermittent sounds.

Playing a CD-R or CD-RW

•Use only “finalized” CD-Rs or CD-RWs.

•This unit can only play back files of the same type as those which are detected first if a disc includes both audio CD (CD-DA) files and MP3/WMA files.

•This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.

•Some CD-Rs or CD-RWs may not be played back on this unit because of their disc characteristics, or for the following reasons:

–Discs are dirty or scratched.

–Moisture condensation has occurred on the lens inside the unit.

–The pickup lens inside the unit is dirty.

–The files on the CD-R/CD-RW are written using the “Packet Write” method.

–There are improper recording conditions (missing data, etc.) or media conditions (stained, scratched, warped, etc.).

•CD-RWs may require a longer readout time since the reflectance of CD-RWs is lower than that of regular CDs.

•Do not use the following CD-Rs or CD-RWs:

–Discs with stickers, labels, or protective seal stuck to the surface.

–Discs on which labels can be directly printed by an

ink jet printer.

Using these discs under high temperature or high humidity may cause malfunctions or damage to the unit.

Playing an MP3/WMA disc

•This unit can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower).

•This unit can show the names of albums, artists (performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for MP3 files and for WMA files.

•This unit can display only one-byte characters. No other characters can be correctly displayed.

•This unit can play back MP3/WMA files meeting the conditions below:

–Bit rate: 8 kbps — 320 kbps

–Sampling frequency:

48 kHz, 44.1 kHz, 32 kHz (for MPEG-1) 24 kHz, 22.05 kHz, 16 kHz (for MPEG-2) 12 kHz, 11.025 kHz, 8 kHz (for MPEG-2.5)

–Disc format: ISO 9660 Level 1/ Level 2, Romeo, Joliet, Windows long file name

–Bit rate of WMA: 16 kbps — 32 kbps

(Sampling frequency: 22.05 kHz) 32 kbps — 320 kbps (Sampling frequency: 48 kHz,

44.1kHz, 32 kHz)

•The maximum number of characters for file/folder names vary depending on the disc format used (includes 4 extension characters—<.mp3> or <.wma>).

–ISO 9660 Level 1: up to 12 characters

–ISO 9660 Level 2: up to 31 characters

–Romeo: up to 128 characters

–Joliet: up to 64 characters

–Windows long file name: up to 128 characters

•This unit can recognize a total of 512 files, 255 folders, and 8 hierarchical levels.

•This unit can play back files recorded in VBR (variable bit rate).

Files recorded in VBR have a discrepancy in the elapsed time display, and do not show the actual elapsed time. In particular, this difference becomes noticeable after performing the search function.

•This unit cannot play back the following files:

–MP3 files encoded in MP3i and MP3 PRO format.

–MP3 files encoded in an inappropriate format.

–MP3 files encoded with Layer 1/2.

–WMA files encoded in lossless, professional, and voice format.

–WMA files not based on Windows Media® Audio.

–WMA files copy-protected with DRM.

–Files which have data such as WAVE, ATRAC3, etc.

•The search function works but search speed is not constant.

Playing MP3/WMA tracks from a USB device

•While playing from a USB device, the playback order may differ from other players.

•This unit may be unable to play back some USB devices or some files due to their characteristics or recording conditions.

•Depending on the shape of the USB devices and connection ports, some USB devices may not be attached properly or the connection might be loose.

•When connecting a USB mass storage class device, refer also to its instructions.

•Connect one USB mass storage class device to the unit at a time. Do not use a USB hub.

•If the connected USB device does not have the correct files, “NO FILE” appears.

•This unit can show Tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for MP3 files and for WMA files.

Continued on the next page

•This unit can play back MP3/WMA files meeting the conditions below:

–Bit rate of MP3: 16 kbps — 320 kbps

–Sampling frequency of MP3:

48 kHz, 44.1 kHz, 32 kHz (for MPEG-1) 24 kHz, 22.05 kHz, 16 kHz (for MPEG-2) 12 kHz, 11.025 kHz, 8 kHz (for MPEG-2.5)

–Bit rate of WMA: 16 kbps — 32 kbps

(Sampling frequency: 22.05 kHz) 32 kbps — 320 kbps

(Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz)

•This unit can play back MP3 files recorded in VBR (variable bit rate).

•The maximum number of characters for:

–Folder names : 25 characters

–File names : 25 characters

–MP3 Tag : 128 characters

–WMA Tag : 64 characters

•This unit can recognize a total of 2 500 files, 255 folders (999 files per folder), and of 8 hierarchies.

•This unit does not support SD card reader.

•This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 500 mA.

•USB devices equipped with special functions such as data security functions cannot be used with the unit.

•Do not use a USB device with 2 or more partitions.

•This unit may not recognized a USB device connected through a USB card reader.

•This unit may not play back files in a USB device properly when using a USB extension cord.

•This unit cannot play back the following files:

–MP3 files encoded with MP3i and MP3 PRO format.

–MP3 files encoded in an inappropriate format.

–MP3 files encoded with Layer 1/2.

–WMA files encoded in lossless, professional, and voice format.

–WMA files not based on Windows Media® Audio.

Changing the source

•If you change the source, playback also stops.

Next time you select the same source again, playback starts from where it has been stopped previously.

Ejecting a disc or removing a USB device

•If the ejected disc is not removed within 15 seconds, it is automatically inserted into the loading slot again to protect it from dust.

•After ejecting a disc or removing a USB device, “NO DISC” or “NO USB“ appears and you cannot operate some of the buttons. Insert another disc,

reattach a USB device, or press SRC to select another playback source.

General settings—PSM

•“AUTO” setting for “DIMMER” may not work correctly on some vehicles, particularly on those having a control dial for dimming.

In this case, change the “DIMMER” setting to any other than “AUTO.”

•If you change the “AMP GAIN” setting from “HIGH POWER” to “LOW POWER” while the volume level is set higher than “VOLUME 30,” the unit automatically changes the volume level to “VOLUME 30.”

Available characters on the display

Available characters

Display indications

Maintenance

How to clean the connectors

Frequent detachment will deteriorate the connectors. To minimize this possibility, periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors.

To keep discs clean

A dirty disc may not play correctly.

If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge.

•Do not use any solvents (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

Moisture condensation

Moisture may condense on the lens inside the unit in the following cases:

•After starting the heater in the car.

•If it becomes very humid inside the car.

Should this occur, the unit may malfunction. In this case, eject the disc and leave the unit turned on for a few hours until the moisture has evaporated.

How to handle discs

When removing a disc from its

case, press down the center holder of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do not touch its recording surface.

When storing a disc in its case, gently insert the disc around the center holder (with the printed surface facing up).

• Make sure to store discs in cases after use.

To play new discs

New discs may have some rough spots

around the inner and outer edges. If such a disc is used, this unit may reject the disc.

To remove these rough spots, rub the edges with a pencil or ball-point pen, etc.

Do not use the following discs:

Single CD (8 cm disc) Warped disc

Unusual shape

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.