MS-7641
FCC-B Radio FRequenCy inteRFeRenCe Statement
this equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to part 5 of the FCC rules. these limits are designed
to provide reasonable pro-
tection against harmful in-
terference in a residential
installation. this equipment
generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will occur in a particular instal-
lation. if this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the measures
listed below.
Reorient or relocate the receiving antenna.
increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/television technician for
help.
notice
the changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
notice 2
Shielded interface cables and aC power cord, if any, must be used in order to
comply with the emission limits.
VoiR La notiCe d’nStaLLation aVant de RaCCoRdeR au ReSeau.
micro-Star international
mS-764
this device complies with Part 5 of the FCC Rules. operation is subject to the
following two conditions:
this device may not cause harmful interference, and
this device must accept any interference received, including interference that
may cause undesired operation.
PaRt numBeR
G52-764X4
■
■
■
■
)
2)
MS-7641
FCC -B Radio Frequency
Interference
Statement
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable pro-
tection against harmful in-
terference in a residential installation. This equipment
generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below.
■Reorient or relocate the receiving antenna.
■Increase the separation between the equipment and receiver.
■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■Consult the dealer or an experienced radio/television technician for help.
Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
VOIR LA NOTICE D’NSTALLATION AVANT DE RACCORDER AU RESEAU.
Micro-Star International
MS-7641
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
) this device may not cause harmful interference, and
2)this device must accept any interference received, including interference that may cause undesired operation.
Part Number
G52-76411X4
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners.
■MSI® is registered trademark of Micro-Star Int’l Co.,Ltd.
■NVIDIA® is registered trademark of NVIDIA Corporation.
■ATI® is registered trademark of ATI Technologies, Inc.
■AMD® is registered trademarks of AMD Corporation.
■Intel® is registered trademarks of Intel Corporation.
■Windows® is registered trademarks of Microsoft Corporation.
■AMI® is registered trademark of Advanced Micro Devices, Inc.
■Award® is a registered trademark of Phoenix Technologies Ltd.
■Sound Blaster® is registered trademark of Creative Technology Ltd.
■Realtek® is registered trademark of Realtek Semiconductor Corporation.
■JMicron® is registered trademark of JMicron Technology Corporation.
■Netware® is a registered trademark of Novell, Inc.
■Lucid® is trademark of LucidLogix Technologies, Ltd.
■VIA® is registered trademark of VIA Technologies, Inc.
■ASMedia® is registered trademark of ASMedia Technology Inc.
■iPad, iPhone, and iPod are trademarks of Apple Inc.
Revision History
Revision |
Revision History |
Date |
V3.0 |
First release |
2011/05 |
MS-7641
Safety Instructions
■Always read the safety instructions carefully.
■Keep this User Manual for future reference.
■Keep this equipment away from humidity.
■Lay this equipment on a reliable flat surface before setting it up.
■The openings on the enclosure are for air convection hence protects the equipment from overheating. Do not cover the openings.
■Make sure the voltage of the power source is at 110/220V before connecting.
■Place the power cord such a way that people can not step on it. Do not place anything over the power cord.
■Always Unplug the Power Cord before inserting any add-on card or module.
■All cautions and warnings on the equipment should be noted.
■Never pour any liquid into the opening that can cause damage or cause electrical shock.
■If any of the following situations arises, get the equipment checked by service personnel:
○The power cord or plug is damaged.
○Liquid has penetrated into the equipment.
○The equipment has been exposed to moisture.
○The equipment does not work well or you can not get it work according to User Manual.
○The equipment has been dropped and damaged.
○The equipment has obvious sign of breakage.
■DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 60°C (140°F), IT MAY DAMAGE THE EQUIPMENT.
CAUTION
Danger of explosion if battery is incorrectly replaced.
For better environmental protection, waste batteries should be collected separately for recycling or special disposal.
WEEE Statement
ENGLISH
To protect the global environment and as an environmentalist, MSI must remind you that…
Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2002/96/EC, which takes effect on August 13, 2005, products of “electrical and electronic equipment”
cannot be discarded as municipal wastes anymore, and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life. MSI will comply with the product take back requirements at the end of life of MSI-branded products that are sold into the EU. You can return these
products to local collection points.
DEUTSCH
Hinweis von MSI zur Erhaltung und Schutz unserer Umwelt
Gemäß der Richtlinie 2002/96/EG über Elektround Elektronik-Altgeräte dürfen Elektround Elektronik-Altgeräte nicht mehr als kommunale Abfälle entsorgt werden. MSI hat europaweit verschiedene Sammelund Recyclingunternehmen beauftragt, die in die Europäische Union in Verkehr gebrachten Produkte, am Ende seines Lebenszyklus zurückzunehmen. Bitte entsorgen Sie dieses Produkt zum gegebenen Zeitpunkt ausschliesslich an einer lokalen Altgerätesammelstelle in Ihrer Nähe.
FRANÇAIS
En tant qu’écologiste et afin de protéger l’environnement, MSI tient à rappeler ceci…
Au sujet de la directive européenne (EU) relative aux déchets des équipement électriques et électroniques, directive 2002/96/EC, prenant effet le 13 août 2005, que les produits électriques et électroniques ne peuvent être déposés dans les décharges ou tout simplement mis à la poubelle. Les fabricants de ces équipements seront obligés de récupérer certains produits en fin de vie. MSI prendra en compte cette exigence relative au retour des produits en fin de vie au sein de la communauté européenne. Par conséquent vous pouvez retourner localement ces matériels dans les points de collecte.
РУССКИЙ
Компания MSI предпринимает активные действия по защите окружающей среды, поэтому напоминаем вам, что….
В соответствии с директивой Европейского Союза (ЕС) по предотвращению загрязнения окружающей среды использованным электрическим и электронным оборудованием (директива WEEE 2002/96/EC), вступающей в силу 13 августа 2005 года, изделия, относящиеся к электрическому и электронному оборудованию, не могут рассматриваться как бытовой мусор, поэтому производители вышеперечисленного электронного оборудования обязаны принимать его для переработки по окончании срока службы. MSI обязуется соблюдать требования по приему продукции, проданной под маркой MSI на территории EC, в переработку по окончании срока службы. Вы можете вернуть эти изделия в специализированные пункты приема.
MS-7641
ESPAÑOL
MSI como empresa comprometida con la protección del medio ambiente, recomienda:
Bajo la directiva 2002/96/EC de la Unión Europea en materia de desechos y/ o equipos electrónicos, con fecha de rigor desde el 13 de agosto de 2005, los productos clasificados como “eléctricos y equipos electrónicos” no pueden ser depositados en los contenedores habituales de su municipio, los fabricantes de equipos electrónicos, están obligados a hacerse cargo de dichos productos al termino de su período de vida. MSI estará comprometido con los términos de recogida de sus productos vendidos en la Unión Europea al final de su periodo de vida. Usted debe depositar estos productos en el punto limpio establecido por el ayuntamiento de su localidad o entregar a una empresa autorizada para la recogida de estos residuos.
NEDERLANDS
Om het milieu te beschermen, wil MSI u eraan herinneren dat….
De richtlijn van de Europese Unie (EU) met betrekking tot Vervuiling van Electrische en Electronische producten (2002/96/EC), die op 13 Augustus 2005 in zal gaan kunnen niet meer beschouwd worden als vervuiling. Fabrikanten van dit soort producten worden verplicht om producten retour te nemen aan het eind van hun levenscyclus. MSI zal overeenkomstig de richtlijn handelen voor de producten die de merknaam MSI dragen en verkocht zijn in de EU. Deze goederen kunnen geretourneerd worden op lokale inzamelingspunten.
SRPSKI
Da bi zaštitili prirodnu sredinu, i kao preduzeće koje vodi računa o okolini i prirodnoj sredini, MSI mora da vas podesti da…
Po Direktivi Evropske unije (“EU”) o odbačenoj ekektronskoj i električnoj opremi, Direktiva 2002/96/EC, koja stupa na snagu od 13. Avgusta 2005, proizvodi koji spadaju pod “elektronsku i električnu opremu” ne mogu više biti odbačeni kao običan otpad i proizvođači ove opreme biće prinuđeni da uzmu natrag ove proizvode na kraju njihovog uobičajenog veka trajanja. MSI će poštovati zahtev o preuzimanju ovakvih proizvoda kojima je istekao vek trajanja, koji imaju MSI oznaku i koji su prodati u EU. Ove proizvode možete vratiti na lokalnim mestima za prikupljanje.
POLSKI
Aby chronić nasze środowisko naturalne oraz jako firma dbająca o ekologię, MSI przypomina, że…
ZgodniezDyrektywąUniiEuropejskiej(“UE”)dotyczącąodpadówproduktówelektrycznych i elektronicznych (Dyrektywa 2002/96/EC), która wchodzi w życie 13 sierpnia 2005, tzw. “produkty oraz wyposażenie elektryczne i elektroniczne “ nie mogą być traktowane jako śmieci komunalne, tak więc producenci tych produktów będą zobowiązani do odbierania ich w momencie gdy produkt jest wycofywany z użycia. MSI wypełni wymagania UE, przyjmując produkty (sprzedawane na terenie Unii Europejskiej) wycofywane z użycia. Produkty MSI będzie można zwracać w wyznaczonych punktach zbiorczych.
TÜRKÇE
Çevreci özelliğiyle bilinen MSI dünyada çevreyi korumak için hatırlatır:
Avrupa Birliği (AB) Kararnamesi Elektrik ve Elektronik Malzeme Atığı, 2002/96/ EC Kararnamesi altında 13 Ağustos 2005 tarihinden itibaren geçerli olmak üzere, elektrikli ve elektronik malzemeler diğer atıklar gibi çöpe atılamayacak ve bu elektonik cihazların üreticileri, cihazların kullanım süreleri bittikten sonra ürünleri geri toplamakla yükümlü olacaktır. Avrupa Birliği’ne satılan MSI markalı ürünlerin kullanım süreleri bittiğinde MSI ürünlerin geri alınması isteği ile işbirliği içerisinde olacaktır. Ürünlerinizi yerel toplama noktalarına bırakabilirsiniz.
ČESKY
Záleží nám na ochraně životního prostředí — společnost MSI upozorňuje…
Podle směrnice Evropské unie (“EU”) o likvidaci elektrických a elektronických výrobků 2002/96/EC platné od 13. srpna 2005 je zakázáno likvidovat “elektrické a elektronické výrobky” v běžném komunálním odpadu a výrobci elektronických výrobků, na které se tato směrnice vztahuje, budou povinni odebírat takové výrobky zpět po skončení jejich životnosti. Společnost MSI splní požadavky na odebírání výrobků značky MSI, prodávaných v zemích EU, po skončení jejich životnosti. Tyto výrobky můžete odevzdat v místních sběrnách.
MAGYAR
Annak érdekében, hogy környezetünket megvédjük, illetve környezetvédőként fellépve az MSI emlékezteti Önt, hogy …
Az Európai Unió („EU”) 2005. augusztus 13-án hatályba lépő, az elektromos és elektronikus berendezések hulladékairól szóló 2002/96/EK irányelve szerint az elektromos és elektronikus berendezések többé nem kezelhetőek lakossági hulladékként, és az ilyen elektronikus berendezések gyártói kötelessé válnak az ilyen termékek visszavételére azok hasznos élettartama végén. Az MSI betartja a termékvisszavétellel kapcsolatos követelményeket az MSI márkanév alatt az EU-n belül értékesített termékek esetében, azok élettartamának végén. Az ilyen termékeket a legközelebbi gyűjtőhelyre viheti.
ITALIANO
Per proteggere l’ambiente, MSI, da sempre amica della natura, ti ricorda che…. In base alla Direttiva dell’Unione Europea (EU) sullo Smaltimento dei Materiali Elettrici ed Elettronici, Direttiva 2002/96/EC in vigore dal 13 Agosto 2005, prodotti appartenenti alla categoria dei Materiali Elettrici ed Elettronici non possono più essere eliminati come rifiuti municipali: i produttori di detti materiali saranno obbligati a ritirare ogni prodotto alla fine del suo ciclo di vita. MSI si adeguerà a tale Direttiva ritirando tutti i prodotti marchiati MSI che sono stati venduti all’interno dell’Unione Europea alla fine del loro ciclo di vita. È possibile portare i prodotti nel più vicino punto di raccolta
MS-7641 |
Table of Content |
English.…………………………………………………………………..9 |
Getting startED………………………………………………………………………………9 |
SPECIFICATIONS………………………………………………………………………………..10 |
Screw Holes…………………………………………………………………………………..12 |
REAR PANEL………………………………………………………………………………………13 |
HARDWARE SETUP…………………………………………………………………………….13 |
BIOS Setup……………………………………………………………………………………….22 |
.……………………………………………………………………..29 |
.…………………………………………………………………………………………….29 |
.…………………………………………………………………………………………………..30 |
.……………………………………………………………………………………………32 |
.……………………………………………………………………………………………33 |
………………………………………………………………………………………33 |
BIOS ……………………………………………………………………………………………42 |
Français………………………………………………………………..49 |
Pour commencer.…………………………………………………………………………49 |
SPéCIFICATIONS………………………………………………………………………………..50 |
Trous taraudés.……………………………………………………………………………52 |
Panneau arrière……………………………………………………………………………53 |
Installation du matériel……………………………………………………………..53 |
Réglage bios…………………………………………………………………………………..62 |
DEUTSCH…………………………………………………………………69 |
eINLEITUNG……………………………………………………………………………………….69 |
SPEZIFIKATIONEN………………………………………………………………………………70 |
SCHRAUBENLÖCHER…………………………………………………………………………72 |
Hinteres Anschlusspanel……………………………………………………………73 |
HARDWARE SETUP…………………………………………………………………………….73 |
BIOS Setup……………………………………………………………………………………….82 |
РУССКИЙ…………………………………………………………………89 |
НАЧАЛО РАБОТЫ………………………………………………………………………………89 |
ХАРАКТЕРИСТИКИ…………………………………………………………………………….90 |
ОТВЕРСТИЯ ДЛЯ ВИНТОВ…………………………………………………………………92 |
ЗАДНЯЯ ПАНЕЛЛЬ.……………………………………………………………………………93 |
УСТАНОВКА ОБОРУДОВАНИЯ.………………………………………………………….93 |
НАСТРОЙКА BIOS…………………………………………………………………………….102 |
…………………………………………………………………. |
109 |
.………………………………………………………………………………………………… |
109 |
.………………………………………………………………………………………………… |
110 |
………………………………………………………………………………………………. |
112 |
.………………………………………………………………………………………….. |
113 |
.………………………………………………………………………………………….. |
113 |
BIOS …………………………………………………………………………………………. |
122 |
…………………………………………………………………. |
129 |
.………………………………………………………………………………………………… |
129 |
.………………………………………………………………………………………………… |
130 |
………………………………………………………………………………………………. |
132 |
.………………………………………………………………………………………………… |
133 |
.………………………………………………………………………………………….. |
133 |
BIOS …………………………………………………………………………………………. |
142 |
.…………………………………………………………………… |
149 |
.………………………………………………………………………………………….. |
149 |
.………………………………………………………………………….. |
150 |
………………………………………………………………………………………………. |
152 |
I/O ………………………………………………………………………………………….. |
153 |
.………………………………………………………………… |
153 |
BIOS ………………………………………………………………………………………. |
162 |
MS-7641
English
Getting startED
Thank you for choosing the 760GM-P25 (FX)/ 760GM-P23 (FX)/ 760GM-P21 (FX) (MS-7641 v3.x) Micro-ATX mainboard. The 760GM-P25 (FX)/ 760GM-P23 (FX)/ 760GM-P21 (FX) is based on AMD® 760G & SB710 chipset for optimal system efficiency. Designed to fit the advanced AMD® processor in AM3+ package, the 760GM-P25 (FX)/ 760GM-P23 (FX)/ 760GM-P21 (FX) Series deliver a high performance and professional desktop platform solution.
Layout
Top : mouse
Bottom:keyboard
Top: VGA Port |
Bottom: DVI-D Port (optional) |
USB2.0 ports
USB2.0 ports
Top: LAN Jack Bottom: USB ports
JUSB_PW1
JPWR2
CPUFAN
DIMM1 DIMM2
T:Line-I n M:Line-O ut B:Mic
T:RS-Ou t
M:CS-Ou t (optional) B:SS-O ut
JCI1
JAUD1
SYSFAN1
AMD 760G
PCI_E1
PCI_E2
AMD SB710
PCI1
JFP2 |
|||
JSP1 |
JCOM1 |
JTPM1 |
|
JUSB_PW2 JUSB1 JUSB2 |
JFP1 |
BUZ1
JPWP1
JBAT1
BATT
+
SATA3 SATA6
SPECIFICATIONS
Processor
■ AMD® Phenom II/ Athlon II/ Sempron processors in the AM3+ package.
(For the latest information about CPU, please visit http://www.msi.com/service/cpu-support/)
HyperTransport
■ HyperTransport™ 3.0, supports up to 5.2 GT/s Chipset
■North Bridge: AMD® 760G chipset
■South Bridge: AMD® SB710 chipset
Memory
■DDR3 800/ 1066/ 1333 SDRAM (total 16GB Max)
■2 DDR3 DIMMs (240pin / 1.5V)
(For more information on compatible components, please visit http://www.msi.com/service/test-report/)
LAN
■Supports LAN 10/100/1000 Fast Ethernet by Realtek® 8111E (760GM-P25 (FX)/ 760GM-P23 (FX))
■Supports LAN 10/100 Fast Ethernet by Realtek® 8105E (760GM-P21 (FX))
Audio
■Chip integrated by Realtek® ALC892 (760GM-P25 (FX))
■Chip integrated by Realtek® ALC887 (760GM-P23 (FX)/ 760GM-P21 (FX))
■Supports 7.1 channels audio out
■Compliant with Azalia 1.0 Spec
SATA
■ 6 SATA 3Gb/s ports by AMD® SB710
RAID
■ SATA 1~6 support RAID 0/ 1/ 10 or JBOD mode by AMD® SB710 Connectors
■Back Panel I/O
1 PS/2 mouse port
1 PS/2 keyboard port
1 VGA port
1 DVI-D port (760GM-P25 (FX)/ 760GM-P23 (FX))
6 USB 2.0 ports
1 LAN jack
6 flexible audio jacks (760GM-P25 (FX))
3 flexible audio jacks (760GM-P23 (FX)/ 760GM-P21 (FX))
■Onboard Connectors
2 USB 2.0 connectors
1 S/PDIF-Out connector
1 front audio connector
1 chassis Intrusion connector
1 serial port connecotr
1 TPM connector
10
MS-7641
Slots
■1 PCIE x16 slot
■1 PCIE x1 slot
■1 PCI slot, supports 3.3V/ 5V PCI bus Interface
Form Factor
■ Micro-ATX (205mm x 244mm)
Mounting
■ 6 mounting holes
If you need to purchase accessories and request the part numbers, you could search the product web page and find details on our web address below http://www.msi.com/index.php
11
Screw Holes
When you install the mainboard, you have to place the mainboard into the chassis in the correct direction. The locations of screws holes on the mainboard are shown as below.
The side has to toward the rear,
the position for the
I/O shield of the chassis.
Screw holes
Refer above picture to install standoffs in the appropriate locations on chassis and then screw through the mainboard screw holes into the standoffs.
Important
*Topreventdamagetothemainboard,anycontactbetweenthemainboardcircuit and chassis or unnecessary standoffs mounted on the chassis is prohibited.
*Please make sure there is no metal components placed on the mainboard or within the chassis that may cause short circuit of the mainboard.
12
MS-7641
REAR PANEL
The rear panel provides the following connectors:
Mouse |
VGA Port |
LAN |
||
Line-In |
RS-Out |
|||
Line-Out |
CS-Out |
|||
Keyboard |
DVI-D Port |
USB 2.0 Ports |
MIC |
SS-Out |
(optional) |
(optional) |
|||
HARDWARE SETUP
CPU & Cooler Installation for AM3+
When you are installing the CPU, make sure the CPU has a cooler attached on the top to prevent overheating. Meanwhile, do not forget to apply some thermal paste on CPU before installing the heat sink/cooler fan for better heat dispersion.
The surface of AM3+ CPU.
Remember to apply some thermal paste on it
for better heat dispersion.
Gold arrow
13
Follow the steps below to install the CPU & cooler correctly. Wrong installation will cause the damage of your CPU & mainboard.
. Pull the lever sideways away from the socket. Make sure to raise the lever up to a 90-degree angle.
2.Look for the gold arrow of the CPU. The gold
arrow should point as shown in the picture. The CPU can only fit in the correct orientation.
3. If the CPU is correctly installed, the pins should be completely embedded into the socket and can not be seen. Please note that any violation of the correct installation procedures may cause permanent damages to your mainboard.
4. Press the CPU down firmly into the socket and close the lever. As the CPU is likely to move while the lever is being closed, always close the lever with your fingers pressing tightly on top of the CPU to make sure the CPU is properly and completely embedded into the socket.
5. Position the cooling set onto the retention mechanism. Hook one end of the clip to hook first.
6. Then press down the other end of the clip to fasten the cooling set on the top of the retention mechanism. Locate the Fix Lever and lift up it .
7. Fasten down the lever.
8.Attach the CPU Fan cable to the CPU fan connector on the mainboard.
Important
While disconnecting the Safety Hook from the fixed bolt, it is necessary to keep an eye on your fingers, because once the Safety Hook is disconnected from the fixed bolt, the fixed lever will spring back instantly.
14
MS-7641
Installing Memory Modules
. The memory module has only one notch on the center and will only fit in the right orientation.
2.Insert the memory module vertically into the DIMM slot. Then push it in until the golden finger on the memory module is deeply inserted in the DIMM slot. The plastic clip at each side of the DIMM slot will automatically close when the
memory module is properly seated. You can barely see the golden finger if the memory module is
properly inserted
in
the DIMM slot.
3.Manually check if the memory module has been locked in place by the DIMM slot clips at the sides.
Notch
Volt
Important
*In Dual-Channel mode, make sure that you install memory modules of the same type and density in different channel DIMM slots.
*To enable successful system boot-up, always insert the memory modules into the DIMM1 first.
15
ATX 24-Pin Power Connector: JPWR1
This connector allows you to connect an ATX 24-pin power supply. To connect the ATX 24-pin power supply, make sure the plug of the power supply is inserted in the proper orientation and the pins are aligned. Then push down the power supply firmly into the connector.
12. |
|||||||||||||||
11 |
. +3 |
. |
|||||||||||||
910. |
|||||||||||||||
8 |
. |
+12V |
3V |
||||||||||||
7 |
|||||||||||||||
6 . |
|||||||||||||||
5 . |
|||||||||||||||
4 |
. +5 |
||||||||||||||
2 |
3 . |
||||||||||||||
. +5 |
V |
||||||||||||||
1 |
. |
||||||||||||||
Ground |
|||||||||||||||
. +3. |
24 |
||||||||||||||
3 |
|||||||||||||||
+3.Ground |
. |
||||||||||||||
3 |
V |
||||||||||||||
V |
23. |
||||||||||||||
. +5 |
V |
||||||||||||||
+5 |
|||||||||||||||
Ground |
|||||||||||||||
+5 |
V |
V |
|||||||||||||
. |
— |
||||||||||||||
13. — |
ON |
# |
|||||||||||||
12V |
|||||||||||||||
+3.Ground |
|||||||||||||||
3 |
|||||||||||||||
V |
ATX 4-Pin Power Connector: JPWR2
This 4-Pin power connector is used to provide power to the CPU.
1 |
||
. |
||
2 |
Ground |
|
. |
||
Ground |
||
3 |
||
4 |
. |
|
. |
||
+12V |
||
+12V |
Important
Make sure that all the connectors are connected to proper ATX power supplies to ensure stable operation of the mainboard.
Serial ATA Connector:
SATA1 ~ 6
This connector is a high-speed Serial ATA interface port. Each connector can connect to one Serial ATA device.
Important
Please do not fold the Serial ATA cable into a 90-degree angle. Otherwise, data loss may occur during transmission.
16
MS-7641
Fan Power Connectors:
CPUFAN, SYSFAN1
The fan power connectors support system cooling fan with +12V. When connecting the wire to the connectors, always note that the red wire is the positive and should be connected to the +12V; the black wire is Ground and should be connected to GND. If the mainboard has a System Hardware Monitor chipset onboard, you must use a specially designed fan with speed sensor to take advantage of the CPU fan control.
CPUFAN SYSFAN1
1 |
||||||||
2 . |
||||||||
3 |
. G |
|||||||
4 |
. |
+ |
o |
|||||
S 1 |
u |
|||||||
. |
e 2 |
n |
||||||
C |
n V |
d |
||||||
o |
s |
|||||||
n |
||||||||
t o |
||||||||
r r |
||||||||
o |
||||||||
l |
1 |
||||||
2 . |
||||||
3 |
. G |
|||||
+ r |
||||||
. |
1 o |
|||||
S |
2 u |
|||||
e |
n |
|||||
n V |
d |
|||||
s |
||||||
o |
||||||
r |
S/PDIF-Out Connector:
JSP1
This connector is used to connect S/PDIF (Sony & Philips Digital Interconnect Format) interface for digital audio transmission.
1 |
||||||
2 . |
||||||
3 |
. Gr |
|||||
S |
o |
|||||
. |
P |
u |
||||
V |
D |
n |
||||
C |
I |
d |
||||
C |
F |
Front Panel
Connectors:
JFP1, JFP2
These connectors are for electrical connection to the front panel switches and LEDs. The JFP1 is compliant with Intel® Front Panel I/O Connectivity Design Guide.
P |
||||||||
P |
ower |
S |
10. |
|||||
ower |
LE |
witch |
No |
|||||
8Pi |
||||||||
D |
6 |
. n |
||||||
— |
||||||||
4 |
. |
|||||||
+ |
||||||||
2 |
. |
|||||||
— |
||||||||
. |
||||||||
+ |
JFP1
9 |
||||||||||
1 — |
. |
|||||||||
7 |
Reserve |
|||||||||
5 |
. |
|||||||||
+ |
||||||||||
3 |
. |
|||||||||
— |
||||||||||
. |
d |
|||||||||
+ |
||||||||||
. |
Reset |
|||||||||
S |
||||||||||
HDD |
LE |
|||||||||
D |
witch |
Speaker |
6 |
+ |
|||
Buzzer |
|||||
8 |
|||||
. |
|||||
4 |
. |
||||
— |
|||||
2 |
. |
||||
+ |
|||||
. |
|||||
— |
JFP2
7 |
||||||
3 |
5 . |
|||||
. No |
||||||
1 |
Power |
|||||
. |
Pi |
|||||
. |
Suspend |
D |
||||
n |
||||||
Ground |
LE |
|||||
LE |
||||||
D |
17
Serial Port Connector:
JCOM1 This connector is a 16550A high 16 bytes FIFOs. You can attach a
speed communication port that sends/receives serial device.
1 |
||||||||||
0 |
||||||||||
8 . |
||||||||||
6 |
. N |
|||||||||
C |
o |
|||||||||
4 |
. |
T |
P |
|||||||
D |
S |
i |
||||||||
2 |
. |
S |
n |
|||||||
D |
R |
|||||||||
. |
T |
|||||||||
S |
R |
|||||||||
I |
||||||||||
N |
9 |
||||||||
7 |
. |
|||||||
5 |
R |
|||||||
. |
I |
|||||||
3 |
. R |
|||||||
T |
||||||||
1 |
. Gr |
S |
||||||
S |
o |
|||||||
. |
O |
u |
||||||
D |
U |
n |
||||||
C |
T |
d |
||||||
D |
Front Panel
Audio Connector:
JAUD1
This connector allows you to connect the front panel audio and is compliant with Intel® Front Panel I/O Connectivity Design Guide.
1 |
|||||||||||||||||||
0 |
|||||||||||||||||||
8 . |
|||||||||||||||||||
6 |
. |
H |
|||||||||||||||||
N |
e |
||||||||||||||||||
. |
o |
a |
|||||||||||||||||
4 |
M |
P |
P |
||||||||||||||||
2 |
. |
I |
i |
||||||||||||||||
P |
C |
n |
h |
||||||||||||||||
. |
R |
D |
o |
||||||||||||||||
G |
E |
e |
n |
||||||||||||||||
r |
S |
t |
e |
||||||||||||||||
o |
e |
D |
|||||||||||||||||
u |
E |
c |
t |
||||||||||||||||
n |
N |
i |
|||||||||||||||||
d |
C |
o |
e |
||||||||||||||||
E |
n |
c |
|||||||||||||||||
t |
|||||||||||||||||||
# |
i |
||||||||||||||||||
o |
|||||||||||||||||||
n |
9 |
||||||||||||||||
7 |
. |
|||||||||||||||
H |
||||||||||||||||
5 |
. |
e |
||||||||||||||
S |
a |
|||||||||||||||
3 |
. |
E |
||||||||||||||
H |
d |
|||||||||||||||
1 |
. |
e |
N |
P |
||||||||||||
M |
a |
S |
h |
|||||||||||||
. |
I |
d |
E |
o |
||||||||||||
M |
C |
P |
_ |
n |
||||||||||||
I |
R |
S |
e |
|||||||||||||
C |
h |
L |
||||||||||||||
L |
o |
E |
||||||||||||||
n |
N |
|||||||||||||||
e |
D |
|||||||||||||||
R |
Front USB Connector:
JUSB1, JUSB2
This connector, compliant with Intel® I/O Connectivity Design Guide, is ideal for connecting high-speed USB interface peripherals such as USB HDD, digital cameras, MP3 players, printers, modems and the like.
1 |
|||||||||||
0 |
|||||||||||
6 |
8 . |
||||||||||
G NC |
|||||||||||
. |
. |
r |
|||||||||
4 |
|||||||||||
U |
o |
||||||||||
2 |
. |
S |
u |
||||||||
U |
B |
n |
|||||||||
. |
S |
1 |
d |
||||||||
V |
B |
+ |
|||||||||
C |
1 |
||||||||||
C |
— |
9 |
|||||||||
7 |
. |
||||||||
N |
|||||||||
5 . |
o |
||||||||
3 |
. Gr |
P |
|||||||
U |
o |
i |
|||||||
1 |
. |
S |
u n |
||||||
U |
n |
||||||||
. |
S |
B |
d |
||||||
V |
B |
0 |
|||||||
C |
0 |
+ |
|||||||
C |
— |
18
MS-7641
TPM Module connector: JTPM1
This connector connects to a TPM (Trusted Platform Module) module. Please refer to the TPM security platform manual for more details and usages.
1 |
|||||||||||||||||||||||||||||||||||||||||||||||||
4 |
|||||||||||||||||||||||||||||||||||||||||||||||||
1 . |
|||||||||||||||||||||||||||||||||||||||||||||||||
1 |
2 |
||||||||||||||||||||||||||||||||||||||||||||||||
. Gr |
|||||||||||||||||||||||||||||||||||||||||||||||||
. G |
o |
||||||||||||||||||||||||||||||||||||||||||||||||
8 |
0 |
r |
|||||||||||||||||||||||||||||||||||||||||||||||
N |
u |
||||||||||||||||||||||||||||||||||||||||||||||||
6 |
. |
o |
n |
||||||||||||||||||||||||||||||||||||||||||||||
5 |
o |
u |
d |
||||||||||||||||||||||||||||||||||||||||||||||
4 |
. |
V |
P |
n |
|||||||||||||||||||||||||||||||||||||||||||||
S |
P |
i |
d |
||||||||||||||||||||||||||||||||||||||||||||||
. |
e |
n |
|||||||||||||||||||||||||||||||||||||||||||||||
3 |
i o |
||||||||||||||||||||||||||||||||||||||||||||||||
2 . |
r |
w |
|||||||||||||||||||||||||||||||||||||||||||||||
a |
|||||||||||||||||||||||||||||||||||||||||||||||||
. |
3 |
l |
e |
||||||||||||||||||||||||||||||||||||||||||||||
3 |
V |
I |
r |
||||||||||||||||||||||||||||||||||||||||||||||
V |
t |
P |
R |
||||||||||||||||||||||||||||||||||||||||||||||
o |
Q |
||||||||||||||||||||||||||||||||||||||||||||||||
S |
a |
w |
|||||||||||||||||||||||||||||||||||||||||||||||
n |
e |
||||||||||||||||||||||||||||||||||||||||||||||||
d |
r |
||||||||||||||||||||||||||||||||||||||||||||||||
b |
|||||||||||||||||||||||||||||||||||||||||||||||||
y |
|||||||||||||||||||||||||||||||||||||||||||||||||
p |
|||||||||||||||||||||||||||||||||||||||||||||||||
o |
|||||||||||||||||||||||||||||||||||||||||||||||||
w |
1 |
||||||||||||||||||||||||||||||||||||||||||||||||
e |
|||||||||||||||||||||||||||||||||||||||||||||||||
r |
3 |
||||||||||||||||||||||||||||||||||||||||||||||||
1 . |
|||||||||||||||||||||||||||||||||||||||||||||||||
9 |
1 |
L |
|||||||||||||||||||||||||||||||||||||||||||||||
. |
P |
||||||||||||||||||||||||||||||||||||||||||||||||
7 |
. |
L |
C |
||||||||||||||||||||||||||||||||||||||||||||||
L |
P |
F |
|||||||||||||||||||||||||||||||||||||||||||||||
5 |
. |
P |
C |
||||||||||||||||||||||||||||||||||||||||||||||
L |
C |
a |
r |
||||||||||||||||||||||||||||||||||||||||||||||
3 |
. |
P |
a |
a |
|||||||||||||||||||||||||||||||||||||||||||||
L |
C |
d |
m |
||||||||||||||||||||||||||||||||||||||||||||||
1 |
. |
P |
d |
d |
e |
||||||||||||||||||||||||||||||||||||||||||||
L |
a |
d |
r |
||||||||||||||||||||||||||||||||||||||||||||||
. |
P C |
d |
r |
e |
|||||||||||||||||||||||||||||||||||||||||||||
L |
C |
a |
d |
e |
s |
||||||||||||||||||||||||||||||||||||||||||||
P |
d |
r |
s |
s |
|||||||||||||||||||||||||||||||||||||||||||||
C |
R |
d |
e |
s |
& |
||||||||||||||||||||||||||||||||||||||||||||
C |
e |
r |
s |
& |
d |
||||||||||||||||||||||||||||||||||||||||||||
s |
e |
s |
d |
a |
|||||||||||||||||||||||||||||||||||||||||||||
l |
e |
s |
& |
t |
|||||||||||||||||||||||||||||||||||||||||||||
o |
t |
s |
a |
a |
|||||||||||||||||||||||||||||||||||||||||||||
c |
& |
d |
t |
||||||||||||||||||||||||||||||||||||||||||||||
k |
a |
p |
|||||||||||||||||||||||||||||||||||||||||||||||
d |
a |
p |
i |
||||||||||||||||||||||||||||||||||||||||||||||
t |
n |
||||||||||||||||||||||||||||||||||||||||||||||||
a |
a |
i |
|||||||||||||||||||||||||||||||||||||||||||||||
t |
p |
n |
3 |
||||||||||||||||||||||||||||||||||||||||||||||
a |
i |
2 |
|||||||||||||||||||||||||||||||||||||||||||||||
p |
n |
||||||||||||||||||||||||||||||||||||||||||||||||
n |
1 |
||||||||||||||||||||||||||||||||||||||||||||||||
i |
|||||||||||||||||||||||||||||||||||||||||||||||||
0 |
Chassis Intrusion Connector:
JCI1
This connector connects to the chassis intrusion switch cable. If the chassis is opened, the chassis intrusion mechanism will be activated. The system will record this status and show a warning message on the screen. To clear the warning, you must enter the BIOS utility and clear the record.
2 |
|||||||
1 |
. |
||||||
G |
|||||||
. |
r |
||||||
CI |
u |
||||||
N |
o |
n |
|||||
T |
d |
||||||
R |
|||||||
U |
Clear CMOS Jumper: JBAT1
There is a CMOS RAM onboard that has a power supply from an external battery to keep the data of system configuration. With the CMOS RAM, the system can automatically boot OS every time it is turned on. If you want to clear the system configuration, set the jumper to clear data.
JBAT1 |
|
1 |
1 |
Keep Data |
Clear Data |
Important
You can clear CMOS by shorting 1-2 pin while the system is off, then open it. Avoid clearing the CMOS while the system is on; it will damage the mainboard.
19
USB power Jumper: JUSB_PW1, JUSB_PW2
These jumpers are used to select USB ports powered by VCC5 or 5VSB. Set to 5VSB if you want the USB ports provide power in standby mode.
JUSB_PW1 |
1 |
1 |
1 |
(for rear USB |
|||
2.0 ports) |
|||
Keep USB |
Keep USB |
||
power to VCC5 |
power to 5VSB |
||
JUSB_PW2 |
|||
(for on-board |
1 |
1 |
1 |
USB connec- |
Keep USB |
Keep USB |
|
tors) |
power to VCC5 |
power to 5VSB |
Important
If you set the jumper to 5VSB, the power supply must be able to provide at least 2A currents.
20
MS-7641
PCIE Slot
The PCIE slot supports the PCIE interface expansion card.
PCIE x16 slot.
PCIE x1 slot.
PCI Slot
The PCI slot supports LAN card, SCSI card, USB card, and other add-on cards that comply with PCI specifications.
Important
When adding or removing expansion cards, make sure that you unplug the power supply first. Read the documentation for the expansion card to configure any necessary hardware or software settings for, such as jumpers, switches or BIOS configuration.
PCI Interrupt
Request Routing
The IRQ, acronym of interrupt request line and pronounced I-R-Q, are hardware lines over which devices can send interrupt signals to the microprocessor. The PCI IRQ pins are typically connected to the PCI bus pins as follows:
Order |
1 |
2 |
3 |
4 |
|||||
Slot |
|||||||||
PCI 1 |
INT E# |
INT F# |
INT G# |
INT H# |
|||||
21
BIOS Setup
Power on the computer and the system will start POST (Power On Self Test) process. When the message below appears on the screen, press <DEL> key to enter Setup.
Press DEL to enter SETUP
If the message disappears before you respond and you still wish to enter Setup, restart the system by turning it OFF and On or pressing the RESET button. You may also restart the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.
Main Page
Standard CMOS Features
Use this menu for basic system configurations, such as time, date etc.
Advanced BIOS Features
Use this menu to setup the items of special enhanced features.
Integrated Peripherals
Use this menu to specify your settings for integrated peripherals.
Power Management Setup
Use this menu to specify your settings for power management.
H/W Monitor
This entry shows the status of your CPU, fan, warning for overall system status.
Green Power
Use this menu to specify the power phase.
22
MS-7641
BIOS Setting Password
Use this menu to set BIOS setting Password.
Cell Menu
Use this menu to specify your settings for frequency/voltage control.
M-Flash
Use this menu to read/ flash the BIOS from USB media device.
Overclocking Profile
Use this menu to save/ load your settings to/ from CMOS for BIOS.
Load Fail
-Safe Defaults
Use this menu to load the BIOS default values that are factory settings for system operations.
Load Optimized Defaults
Use this menu to load factory default settings into the BIOS for stable system performance operations.
Save & Exit Setup
Save changes to CMOS and exit setup.
Exit Without Saving
Abandon all changes and exit setup.
23
Cell Menu
Current CPU/ DRAM/ CPU-NB Frequency
It shows the current frequency of CPU/ DRAM/ CPU-NB. Read-only.
CPU Specifications
Press <Enter> to enter the sub-menu. This submenu shows the information of installed CPU.
CPU Technology Support
Press <Enter> to enter the sub-menu. This sub-menu shows the technologies that the installed CPU supported.
CPU Feature
Press <Enter> to enter the sub-menu:
AMD Cool’n’Quiet
The Cool’n’Quiet technology can effectively and dynamically lower CPU speed and power consumption.
24
MS-7641
C1E Support
To enable this item to red the CPU power consumption while idle. Not all porcessors support Enhanced Halt tate (C1E).
SVM Support
This item allows you to enable/disable the AMD SVM (Secure Virtual Machine) Technology.
AMD Cool’n’Quiet
The Cool’n’Quiet technology can effectively and dynamically lower CPU speed and power consumption.
Important
To ensure that Cool’n’Quiet function is activated and will be working properly, it is required to double confirm that:
*RunBIOSSetup,andselectCellMenu.UnderCellMenu,findAMDCool’n’Quiet, and set this item to “Enabled”.
*Enter Windows, and select [Start]->[Settings]->[Control Panel]->[Power Op-
tions]. Enter Power Options Properties tag, and select MinimalPower Management
under Power schemes.
C1E Support
To enable this item to read the CPU power consumption while idle. Not all porcessors support Enhanced Halt tate (C1E).
Adjust CPU FSB Frequency
(MHz)
This item allows you to select the CPU Front Side Bus clock frequency (in MHz).
OC Stepping
This item will be enabled after you set the overclocking frequency in the “Adjust CPU FSB Frequency (MHz)”. And the following items will appear. This items will help the system to overclock step by step after system booting up.
Start OC Stepping From (MHz)
This item is used to set the initial base clock. The system will boot with the initial base clock, and start to overclock from initial base clock to set base clock that you set in “Adjust CPU FSB Frequency (MHz)” step by step.
OC Step
This item is used to set how many steps for base colck overclocking.
OC Step Count Timer
This item is used to set the buffer time for every step.
Adjust CPU Ratio
This item is used to adjust CPU clock multiplier (ratio). It is available only when the processor supports this function.
Adjusted CPU Frequency (MHz)
It shows the adjusted CPU frequency. Read-only.
Adjust CPU-NB Ratio
This item is used to adjust CPU-NB ratio.
25
Adjusted CPU-NB Frequency (MHz)
It shows the adjusted CPU-NB frequency. Read-only.
Unlock CPU Core
This item allows you to unlock the additional cores, you could set it [Enabled] and then set Advanced Clock Calibration [Auto] in order to be able to activate the processor cores.
Advanced Clock Calibration
This item is for overclock. Setting to [Auto] allows you to set the CPU Ratio higher. It is available only when the processor supports this function.
CPU Core Control
This item is used to control number of CPU cores. When set to [Auto], the CPU will operate under the default number of cores. When set to [Manual], you will be able to enable/disable the specific CPU core.
Core X
These items are used to enable/disable the core X.
OC Genie Lite
Setting this item to [Enabled] allows the system to detect the maximum FSB clock and to overclock automatically. If overclocking fails to run, you can try the lower FSB clock for overclocking successfully.
Memory-Z
Press <Enter> to enter the sub-menu.
DIMM Memory SPD Information
Press <Enter> to enter the sub-menu. This sub-menu displays the information of installed memory.
Advance DRAM Configuration Press <Enter> to enter the sub-menu.
DRAM Timing Mode
Select whether DRAM timing is controlled by the SPD (Serial Presence Detect) EEPROM on the DRAM module. Setting to [Auto] enables DRAM timings and the following “Advance DRAM Configuration” sub-menu to be determined by BIOS based on the configurations on the SPD. Selecting [Manual] allows users to configure the DRAM timings and the following related “Advance DRAM Configuration” sub-menu manually.
FSB/DRAM Ratio
This item allows you to select the ratio of FSB/ DRAM.
Adjusted DRAM Frequency (MHz)
It shows the adjusted Memory frequency. Read-only.
HT Link
Control
Press <Enter> to enter the sub-menu.
HT Incoming/
Outgoing Link
Width
These items allow you to set the Hyper-Transport Link width. Setting to [Auto], the system will detect the HT link width automatically.
26
MS-7641
HT Link
Speed
This item allows you to set the Hyper-Transport Link speed. Setting to [Auto], the system will detect the HT link speed automatically.
Adjusted HT Link
Frequency
(MHz)
It shows the adjusted HT Link frequency. Read-only.
Auto Disable DRAM/PCI Frequency
When set to [Enabled], the system will remove (turn off) clocks from empty DRAM/ PCI slots to minimize the electromagnetic interference (EMI).
CPU VDD Voltage (V)/ CPU-NB VDD Voltage (V)/ DRAM Voltage (V) These items are used to adjust the voltage of CPU, Memory and chipset.
Spread Spectrum
When the mainboard’s clock generator pulses, the extreme values (spikes) of the pulses create EMI (Electromagnetic Interference). The Spread Spectrum function reduces the EMI generated by modulating the pulses so that the spikes of the pulses are reduced to flatter curves. If you do not have any EMI problem, leave the setting at Disabled for optimal system stability and performance. But if you are plagued by EMI, set to Enabled for EMI reduction. Remember to disable Spread Spectrum if you are overclocking because even a slight jitter can introduce a temporary boost in clock speed which may just cause your overclocked processor to lock up.
Important
*If you do not have any EMI problem, leave the setting at [Disabled] for optimal system stability and performance. But if you are plagued by EMI, select the value of Spread Spectrum for EMI reduction.
*The greater the Spread Spectrum value is, the greater the EMI is reduced, and the system will become less stable. For the most suitable Spread Spectrum value, please consult your local EMI regulation.
*Remember to disable Spread Spectrum if you are overclocking because even a slight jitter can introduce a temporary boost in clock speed which may just cause your overclocked processor to lock up.
27
Load Optimized Defaults
You can load the default values provided by the mainboard manufacturer for the stable performance.
28
MS-7641
760GM-P25 (FX)/ 760GM-P23 (FX)/ 760GM-P21 (FX) (MS-7641 v3.x) MicroATX . 760GM-P25 (FX)/ 760GM-P23 (FX)/ 760GM-P21 (FX) AMD® 760G SB710. AM3+ AMD®760GM-P25 (FX)/ 760GM-P23 (FX)/ 760GM-P21 (FX).
Top : mouse
Bottom:keyboard
Top: VGA Port |
Bottom: DVI-D Port (optional) |
USB2.0 ports
USB2.0 ports
Top: LAN Jack Bottom: USB ports
JUSB_PW1
JPWR2
CPUFAN
DIMM1 DIMM2
T:Line-I n M:Line-O ut B:Mic
T:RS-Ou t
M:CS-Ou t (optional) B:SS-O ut
JCI1
JAUD1
SYSFAN1
AMD 760G
PCI_E1
PCI_E2
AMD SB710
PCI1
JFP2 |
|||
JSP1 |
JCOM1 |
JTPM1 |
|
JUSB_PW2 JUSB1 JUSB2 |
JFP1 |
BUZ1
JPWP1
JBAT1
BATT
+
SATA3 SATA6
29
■ AM3+ AMD® Phenom II/ Athlon II/ Sempron .
(CPU http://www.msi.com/service/cpu-support/ )
HyperTransport
■ HyperTransport™ 3.0, 5.2 GT/s
■: AMD® 760G
■: AMD® SB710
■DDR3 800/ 1066/ 1333 SDRAM ( 16GB)
■DDR3 DIMM 2 (240 / 1.5V)
( http://www.msi.com/service/test-report/ .)
LAN
■Realtek® 8111E LAN 10/100/1000 Fast Ethernet (760GM-P25 (FX)/ 760GM-P23 (FX))
■Realtek® 8105E LAN 10/100 Fast Ethernet (760GM-P21 (FX))
■Realtek® ALC892 (760GM-P25 (FX))
■Realtek® ALC887 (760GM-P23 (FX)/ 760GM-P21 (FX))
■7.1
■Azalia 1.0 Spec
SATA
■ AMD® SB710 SATA 3Gb/s 6
RAID
■ AMD® SB710 RAID 0/ 1/ 10 JBOD SATA 1~6
■I/O
PS/2 1
PS/2 1
VGA 1
DVI-D 1 (760GM-P25 (FX)/ 760GM-P23 (FX))
USB 2.0 6
LAN 1
6 (760GM-P25 (FX))
3 (760GM-P23 (FX)/ 760GM-P21 (FX))
USB 2.0 2
S/PDIF 1
1
1
1
TPM 1
30
MS-7641
■PCIE x16 1
■PCIE x1 1
■PCI 1 , 3.3V/ 5V PCI
■ Micro-ATX (205mm x 244mm)
■ 6
, http://www.msi.com/index.php .
31
32
MS-7641 |
|||
. |
|||
VGA |
LAN |
||
RS |
|||
CS |
|||
DVI-D |
USB 2.0 |
SS |
|
( ) |
( ) |
||
AM3+ CPU |
|||
. , |
|||
/ CPU . |
|||
AM3+ CPU . |
|||
. |
|||
33 |
CPU. CPU .
. . 90.
2. CPU . . CPU.
3. CPU , ..
4. CPU. CPU, CPUCPU .
5. ..
..
7. .
8. CPU CPU.
,.
34
MS-7641
. , .
2.DIMM .DIMM .DIMM. DIMM
.
3.DIMM.
*, DIMM.
*, DIMM1 .
35
ATX 24 : JPWR1 |
|||||||||||||||
ATX 24 . ATX 24 |
|||||||||||||||
, |
|||||||||||||||
, . |
|||||||||||||||
. |
|||||||||||||||
12. |
|||||||||||||||
11 |
. +3 |
. |
|||||||||||||
910. |
|||||||||||||||
8 |
. |
+12V |
3V |
||||||||||||
7 |
|||||||||||||||
6 . |
|||||||||||||||
5 . |
|||||||||||||||
4 |
. +5 |
||||||||||||||
3 . |
|||||||||||||||
2 . +5 |
V |
||||||||||||||
1 |
. |
||||||||||||||
Ground |
|||||||||||||||
. +3. |
24 |
||||||||||||||
3 |
|||||||||||||||
+3.Ground |
. |
||||||||||||||
3 |
V |
||||||||||||||
V |
23. |
||||||||||||||
. +5 |
V |
||||||||||||||
+5 |
|||||||||||||||
Ground |
|||||||||||||||
+5 |
V |
||||||||||||||
V |
|||||||||||||||
. |
— |
||||||||||||||
13. — |
ON |
# |
|||||||||||||
12V |
|||||||||||||||
+3.Ground |
|||||||||||||||
3 |
|||||||||||||||
V |
|||||||||||||||
ATX 4 : JPWR2 |
|||||||||||||||
4 CPU . |
|||||||||||||||
1 |
|||||||||||||||
2 |
. |
||||||||||||||
Ground |
|||||||||||||||
. |
|||||||||||||||
Ground |
|||||||||||||||
3 |
|||||||||||||||
4 |
. |
||||||||||||||
. |
|||||||||||||||
+12V |
|||||||||||||||
+12V |
|||||||||||||||
ATX |
|||||||||||||||
. |
|||||||||||||||
ATA : SATA1 ~ 6 |
|||||||||||||||
ATA . |
|||||||||||||||
ATA . |
|||||||||||||||
ATA 90 . , |
|||||||||||||||
. |
|||||||||||||||
36 |
MS-7641
: CPUFAN, SYSFAN1
+12V ., +12V ,GND ., CPU .
CPUFAN SYSFAN1
1 |
||||||||
2 . |
||||||||
3 |
. G |
|||||||
4 |
. |
+ |
o |
|||||
S 1 |
u |
|||||||
. |
e 2 |
n |
||||||
C |
n V |
d |
||||||
o |
s |
|||||||
n |
||||||||
t o |
||||||||
r r |
||||||||
o |
||||||||
l |
1 |
||||||
2 . |
||||||
3 |
. G |
|||||
+ r |
||||||
. |
1 o |
|||||
S |
2 u |
|||||
e |
n |
|||||
n V |
d |
|||||
s |
||||||
o |
||||||
r |
S/PDIF :
JSP1
S/PDIF(Sony & Philips Digital Interconnect Format) .
1 |
||||||
2 . |
||||||
3 |
. Gr |
|||||
S |
o |
|||||
. |
P |
u |
||||
V |
D |
n |
||||
C |
I |
d |
||||
C |
F |
:
JFP1, JFP2
LED . JFP1 Intel® Front Panel I/O Connectivity Design Guide .
P |
||||||||
P |
ower |
S |
10. |
|||||
ower |
LE |
witch |
No |
|||||
8Pi |
||||||||
D |
6 |
. n |
||||||
— |
||||||||
4 |
. |
|||||||
+ |
||||||||
2 |
. |
|||||||
— |
||||||||
. |
||||||||
+ |
JFP1
9 |
||||||||||
1 — |
. |
|||||||||
7 |
Reserve |
|||||||||
5 |
. |
|||||||||
+ |
||||||||||
3 |
. |
|||||||||
— |
||||||||||
. |
d |
|||||||||
+ |
||||||||||
. |
Reset |
|||||||||
S |
||||||||||
HDD |
LE |
|||||||||
D |
witch |
Speaker |
6 |
+ |
|||
Buzzer |
|||||
8 |
|||||
. |
|||||
4 |
. |
||||
— |
|||||
2 |
. |
||||
+ |
|||||
. |
|||||
— |
JFP2
7 |
||||||
3 |
5 . |
|||||
. No |
||||||
1 |
Power |
|||||
. |
Pi |
|||||
. |
Suspend |
D |
||||
n |
||||||
Ground |
LE |
|||||
LE |
||||||
D |
37
: JCOM1 |
|||||||||||||||||||||||||||||||||||||||||||||||
16550A 16 FIFO . |
|||||||||||||||||||||||||||||||||||||||||||||||
. |
|||||||||||||||||||||||||||||||||||||||||||||||
1 |
|||||||||||||||||||||||||||||||||||||||||||||||
0 |
|||||||||||||||||||||||||||||||||||||||||||||||
8 . |
|||||||||||||||||||||||||||||||||||||||||||||||
6 |
. N |
||||||||||||||||||||||||||||||||||||||||||||||
C |
o |
||||||||||||||||||||||||||||||||||||||||||||||
4 |
. |
T |
P |
||||||||||||||||||||||||||||||||||||||||||||
D |
S i |
||||||||||||||||||||||||||||||||||||||||||||||
2 |
. |
S |
n |
||||||||||||||||||||||||||||||||||||||||||||
D |
R |
||||||||||||||||||||||||||||||||||||||||||||||
. |
T |
||||||||||||||||||||||||||||||||||||||||||||||
S |
R |
||||||||||||||||||||||||||||||||||||||||||||||
I |
|||||||||||||||||||||||||||||||||||||||||||||||
N |
|||||||||||||||||||||||||||||||||||||||||||||||
9 |
|||||||||||||||||||||||||||||||||||||||||||||||
7 |
. |
||||||||||||||||||||||||||||||||||||||||||||||
R |
|||||||||||||||||||||||||||||||||||||||||||||||
5 . |
I |
||||||||||||||||||||||||||||||||||||||||||||||
3 |
. R |
||||||||||||||||||||||||||||||||||||||||||||||
T |
|||||||||||||||||||||||||||||||||||||||||||||||
1 |
. Gr |
S |
|||||||||||||||||||||||||||||||||||||||||||||
S |
o |
||||||||||||||||||||||||||||||||||||||||||||||
. |
O |
u |
|||||||||||||||||||||||||||||||||||||||||||||
D |
U |
n |
|||||||||||||||||||||||||||||||||||||||||||||
C |
T |
d |
|||||||||||||||||||||||||||||||||||||||||||||
D |
|||||||||||||||||||||||||||||||||||||||||||||||
: JAUD1 |
|||||||||||||||||||||||||||||||||||||||||||||||
, Intel® |
|||||||||||||||||||||||||||||||||||||||||||||||
Front Panel I/O Connectivity Design Guide . |
|||||||||||||||||||||||||||||||||||||||||||||||
1 |
|||||||||||||||||||||||||||||||||||||||||||||||
0 |
|||||||||||||||||||||||||||||||||||||||||||||||
8 . |
|||||||||||||||||||||||||||||||||||||||||||||||
6 |
. |
H |
|||||||||||||||||||||||||||||||||||||||||||||
N |
e |
||||||||||||||||||||||||||||||||||||||||||||||
. |
o |
a |
|||||||||||||||||||||||||||||||||||||||||||||
4 |
M |
P |
P |
||||||||||||||||||||||||||||||||||||||||||||
2 |
. |
I |
i |
||||||||||||||||||||||||||||||||||||||||||||
P |
C |
n |
h |
||||||||||||||||||||||||||||||||||||||||||||
. |
R |
D |
o |
||||||||||||||||||||||||||||||||||||||||||||
G |
E |
e |
n |
||||||||||||||||||||||||||||||||||||||||||||
r |
S |
t |
e |
||||||||||||||||||||||||||||||||||||||||||||
o |
e |
D |
|||||||||||||||||||||||||||||||||||||||||||||
u |
E |
c |
|||||||||||||||||||||||||||||||||||||||||||||
n |
N |
t |
e |
||||||||||||||||||||||||||||||||||||||||||||
d |
C |
o |
e |
||||||||||||||||||||||||||||||||||||||||||||
E |
n |
c |
|||||||||||||||||||||||||||||||||||||||||||||
t |
|||||||||||||||||||||||||||||||||||||||||||||||
# |
i |
||||||||||||||||||||||||||||||||||||||||||||||
o |
|||||||||||||||||||||||||||||||||||||||||||||||
n |
|||||||||||||||||||||||||||||||||||||||||||||||
9 |
|||||||||||||||||||||||||||||||||||||||||||||||
7 |
. |
||||||||||||||||||||||||||||||||||||||||||||||
H |
|||||||||||||||||||||||||||||||||||||||||||||||
5 |
. |
e |
|||||||||||||||||||||||||||||||||||||||||||||
S |
a |
||||||||||||||||||||||||||||||||||||||||||||||
3 |
. |
E |
|||||||||||||||||||||||||||||||||||||||||||||
H |
d |
||||||||||||||||||||||||||||||||||||||||||||||
1 |
. |
e |
N |
P |
|||||||||||||||||||||||||||||||||||||||||||
M |
a |
S |
h |
||||||||||||||||||||||||||||||||||||||||||||
. |
I |
d |
E |
o |
|||||||||||||||||||||||||||||||||||||||||||
M |
C |
P |
_ |
n |
|||||||||||||||||||||||||||||||||||||||||||
I |
R |
S |
e |
||||||||||||||||||||||||||||||||||||||||||||
C |
h |
L |
|||||||||||||||||||||||||||||||||||||||||||||
L |
o |
E |
|||||||||||||||||||||||||||||||||||||||||||||
n |
N |
||||||||||||||||||||||||||||||||||||||||||||||
e |
D |
||||||||||||||||||||||||||||||||||||||||||||||
R |
|||||||||||||||||||||||||||||||||||||||||||||||
USB : JUSB1, JUSB2 |
|||||||||||||||||||||||||||||||||||||||||||||||
Intel® I/O Connectivity Design Guide USB HDD, |
|||||||||||||||||||||||||||||||||||||||||||||||
, MP3 , , USB |
|||||||||||||||||||||||||||||||||||||||||||||||
. |
|||||||||||||||||||||||||||||||||||||||||||||||
1 |
|||||||||||||||||||||||||||||||||||||||||||||||
0 |
|||||||||||||||||||||||||||||||||||||||||||||||
8 . |
|||||||||||||||||||||||||||||||||||||||||||||||
6 |
. |
||||||||||||||||||||||||||||||||||||||||||||||
G NC |
|||||||||||||||||||||||||||||||||||||||||||||||
4 |
. |
r |
|||||||||||||||||||||||||||||||||||||||||||||
U |
o |
||||||||||||||||||||||||||||||||||||||||||||||
2 |
. |
S |
u |
||||||||||||||||||||||||||||||||||||||||||||
U |
B |
n |
|||||||||||||||||||||||||||||||||||||||||||||
. |
S |
1 |
d |
||||||||||||||||||||||||||||||||||||||||||||
V |
B |
+ |
|||||||||||||||||||||||||||||||||||||||||||||
C |
1 |
||||||||||||||||||||||||||||||||||||||||||||||
C |
— |
||||||||||||||||||||||||||||||||||||||||||||||
9 |
|||||||||||||||||||||||||||||||||||||||||||||||
7 |
. |
||||||||||||||||||||||||||||||||||||||||||||||
N |
|||||||||||||||||||||||||||||||||||||||||||||||
5 . |
o |
||||||||||||||||||||||||||||||||||||||||||||||
3 |
. Gr |
P |
|||||||||||||||||||||||||||||||||||||||||||||
U |
o |
i |
|||||||||||||||||||||||||||||||||||||||||||||
. |
S |
u n |
|||||||||||||||||||||||||||||||||||||||||||||
1 |
U |
n |
|||||||||||||||||||||||||||||||||||||||||||||
. |
S |
B |
d |
||||||||||||||||||||||||||||||||||||||||||||
V |
B |
0 |
|||||||||||||||||||||||||||||||||||||||||||||
C |
0 |
+ |
|||||||||||||||||||||||||||||||||||||||||||||
C |
— |
||||||||||||||||||||||||||||||||||||||||||||||
38 |
MS-7641 |
|||||||||||||||||||||||||||||||||||||||||||||||||
TPM : JTPM1 |
|||||||||||||||||||||||||||||||||||||||||||||||||
TPM(Trusted Platform Module) . |
|||||||||||||||||||||||||||||||||||||||||||||||||
TPM . |
|||||||||||||||||||||||||||||||||||||||||||||||||
1 |
|||||||||||||||||||||||||||||||||||||||||||||||||
4 |
|||||||||||||||||||||||||||||||||||||||||||||||||
1 . |
|||||||||||||||||||||||||||||||||||||||||||||||||
1 |
2 |
||||||||||||||||||||||||||||||||||||||||||||||||
. Gr |
|||||||||||||||||||||||||||||||||||||||||||||||||
0 |
o |
||||||||||||||||||||||||||||||||||||||||||||||||
8 |
. G |
u |
|||||||||||||||||||||||||||||||||||||||||||||||
6 |
. |
N |
o |
n |
|||||||||||||||||||||||||||||||||||||||||||||
5 |
o |
u |
d |
||||||||||||||||||||||||||||||||||||||||||||||
4 |
. |
V |
P |
n |
|||||||||||||||||||||||||||||||||||||||||||||
S |
P |
i |
d |
||||||||||||||||||||||||||||||||||||||||||||||
. |
e |
n |
|||||||||||||||||||||||||||||||||||||||||||||||
3 |
r |
||||||||||||||||||||||||||||||||||||||||||||||||
i o |
|||||||||||||||||||||||||||||||||||||||||||||||||
2 . |
a |
w |
|||||||||||||||||||||||||||||||||||||||||||||||
. |
3 |
l |
e |
||||||||||||||||||||||||||||||||||||||||||||||
3 |
V |
I |
r |
||||||||||||||||||||||||||||||||||||||||||||||
V |
P |
R |
|||||||||||||||||||||||||||||||||||||||||||||||
S |
o |
Q |
|||||||||||||||||||||||||||||||||||||||||||||||
t |
|||||||||||||||||||||||||||||||||||||||||||||||||
a |
w |
||||||||||||||||||||||||||||||||||||||||||||||||
n |
e |
||||||||||||||||||||||||||||||||||||||||||||||||
d |
r |
||||||||||||||||||||||||||||||||||||||||||||||||
b |
|||||||||||||||||||||||||||||||||||||||||||||||||
y |
|||||||||||||||||||||||||||||||||||||||||||||||||
p |
|||||||||||||||||||||||||||||||||||||||||||||||||
o |
|||||||||||||||||||||||||||||||||||||||||||||||||
w |
1 |
||||||||||||||||||||||||||||||||||||||||||||||||
e |
|||||||||||||||||||||||||||||||||||||||||||||||||
r |
3 |
||||||||||||||||||||||||||||||||||||||||||||||||
1 . |
|||||||||||||||||||||||||||||||||||||||||||||||||
9 |
1 |
L |
|||||||||||||||||||||||||||||||||||||||||||||||
. |
P |
||||||||||||||||||||||||||||||||||||||||||||||||
7 |
. |
L |
C |
||||||||||||||||||||||||||||||||||||||||||||||
L |
P |
F |
|||||||||||||||||||||||||||||||||||||||||||||||
5 |
. |
P |
C |
||||||||||||||||||||||||||||||||||||||||||||||
L |
C |
a |
r |
||||||||||||||||||||||||||||||||||||||||||||||
3 |
. |
P |
a |
||||||||||||||||||||||||||||||||||||||||||||||
L |
a |
d |
m |
||||||||||||||||||||||||||||||||||||||||||||||
1 |
. |
P C |
d |
d |
e |
||||||||||||||||||||||||||||||||||||||||||||
L |
C |
a |
d |
r |
|||||||||||||||||||||||||||||||||||||||||||||
. |
P |
d |
r |
e |
|||||||||||||||||||||||||||||||||||||||||||||
L |
C |
a |
d |
e |
s |
||||||||||||||||||||||||||||||||||||||||||||
P |
d |
r |
s |
s |
|||||||||||||||||||||||||||||||||||||||||||||
C |
R |
d |
e |
s |
& |
||||||||||||||||||||||||||||||||||||||||||||
C |
e |
r |
s |
& |
d |
||||||||||||||||||||||||||||||||||||||||||||
s |
e |
s |
d |
a |
|||||||||||||||||||||||||||||||||||||||||||||
l |
e |
s |
t |
||||||||||||||||||||||||||||||||||||||||||||||
o |
t |
s & |
a |
a |
|||||||||||||||||||||||||||||||||||||||||||||
c |
& |
d |
t |
||||||||||||||||||||||||||||||||||||||||||||||
k |
a |
p |
|||||||||||||||||||||||||||||||||||||||||||||||
d |
a |
p |
i |
||||||||||||||||||||||||||||||||||||||||||||||
t |
n |
||||||||||||||||||||||||||||||||||||||||||||||||
a |
a |
i |
|||||||||||||||||||||||||||||||||||||||||||||||
t |
p |
n |
3 |
||||||||||||||||||||||||||||||||||||||||||||||
a |
i |
2 |
|||||||||||||||||||||||||||||||||||||||||||||||
p |
n |
||||||||||||||||||||||||||||||||||||||||||||||||
i |
1 |
||||||||||||||||||||||||||||||||||||||||||||||||
n |
|||||||||||||||||||||||||||||||||||||||||||||||||
0 |
|||||||||||||||||||||||||||||||||||||||||||||||||
: JCI1 |
|||||||||||||||||||||||||||||||||||||||||||||||||
. , |
|||||||||||||||||||||||||||||||||||||||||||||||||
. |
|||||||||||||||||||||||||||||||||||||||||||||||||
. , BIOS . |
|||||||||||||||||||||||||||||||||||||||||||||||||
2 |
|||||||||||||||||||||||||||||||||||||||||||||||||
1 |
. |
||||||||||||||||||||||||||||||||||||||||||||||||
G |
|||||||||||||||||||||||||||||||||||||||||||||||||
. |
r |
||||||||||||||||||||||||||||||||||||||||||||||||
CI |
o |
||||||||||||||||||||||||||||||||||||||||||||||||
u |
|||||||||||||||||||||||||||||||||||||||||||||||||
N |
n |
||||||||||||||||||||||||||||||||||||||||||||||||
T |
d |
||||||||||||||||||||||||||||||||||||||||||||||||
R |
|||||||||||||||||||||||||||||||||||||||||||||||||
U |
|||||||||||||||||||||||||||||||||||||||||||||||||
CMOS : JBAT1 |
|||||||||||||||||||||||||||||||||||||||||||||||||
CMOS RAM . CMOS RAM , |
|||||||||||||||||||||||||||||||||||||||||||||||||
OS . , |
|||||||||||||||||||||||||||||||||||||||||||||||||
. |
|||||||||||||||||||||||||||||||||||||||||||||||||
JBAT1 |
1 |
1 |
|||||||||||||||||||||||||||||||||||||||||||||||
1-2 CMOS . |
|||||||||||||||||||||||||||||||||||||||||||||||||
. CMOS . |
|||||||||||||||||||||||||||||||||||||||||||||||||
. |
|||||||||||||||||||||||||||||||||||||||||||||||||
39 |
USB : JUSB_PW1, JUSB_PW2
VCC5 5VSB USB . USB 5VSB .
JUSB_PW1 |
1 |
1 |
1 |
( USB |
|||
2.0 ) |
|||
USB |
USB |
||
VCC5 |
5VSB |
||
JUSB_PW2 |
|||
( USB |
1 |
1 |
1 |
) |
USB |
USB |
|
VCC5 |
5VSB |
5VSB 2A.
40
MS-7641 |
|||||
PCIE |
|||||
PCIE PCIE . |
|||||
PCIE x16 . |
|||||
PCIE x1 . |
|||||
PCI |
|||||
PCI LAN , SCSI , USB PCI |
|||||
. |
|||||
. |
|||||
, BIOS |
|||||
. |
|||||
PCI |
|||||
Interrupt request line IRQ I-R-Q , |
|||||
. PCI IRQ |
|||||
PCI . |
|||||
1 |
2 |
3 |
4 |
||
PCI 1 |
INT E# |
INT F# |
INT G# |
INT H# |
|
41 |
BIOS |
POST(Power On Self Test) . |
, <DEL> . |
Press DEL to enter SETUP |
, |
RESET . <Ctrl>, <Alt> <Delete> |
. |
Standard CMOS Features |
, . |
Advanced BIOS Features |
. |
Integrated Peripherals |
. |
Power Management Setup |
. |
H/W Monitor |
CPU , . |
Green Power |
. |
BIOS Setting Password |
BIOS . |
42 |
MS-7641
Cell Menu
/ .
M-Flash
USB BIOS .
Overclocking Profile
BIOS CMOS ( ) .
Load Fail
-Safe Defaults
BIOS.
Load Optimized Defaults
BIOS.
Save & Exit Setup
CMOS .
Exit Without Saving
.
43
Current CPU/ DRAM/ CPU-NB Frequency
CPU/ DRAM/ CPU-NB . ( ).
CPU Specifications
<Enter> . CPU.
CPU Technology Support
<Enter> . CPU.
CPU Feature
<Enter> .
AMD Cool’n’Quiet
Cool’n’Quiet CPU.
44
MS-7641
C1E Support
CPU ., .
SVM Support
AMD SVM (Secure Virtual Machine) /.
AMD Cool’n’Quiet
Cool’n’Quiet CPU.
Cool’n’Quiet ,.
*BIOS AMD Cool’n’Quiet “Enabled” .
*Windows [Start]->[Settings]->[Control Panel]->[Power Options]. [ ].
C1E Support
CPU ., .
Adjust CPU FSB Frequency
(MHz)
CPU Front Side Bus clock (in MHz).
OC Stepping
“Adjust CPU FSB Frequency (MHz)”. ..
Start OC Stepping From (MHz)
.. “Adjust CPU FSB Frequency (MHz)” .
OC Step
FSB .
OC Step Count Timer
.
Adjust CPU Ratio
CPU ( ) ..
Adjusted CPU Frequency (MHz)
CPU . ( ).
45
Adjust CPU-NB Ratio
CPU-NB .
Adjusted CPU-NB Frequency (MHz)
CPU-NB . ( ).
Unlock CPU Core
, [Enabled][Manual] .
Advanced Clock Calibration
. [Auto] CPU. .
CPU Core Control
CPU . [Auto] CPU. [Manual] CPU/ .
Core X
X / .
OC Genie Lite
[Enabled] FSB. .
Memory-Z
<Enter> .
DIMM Memory SPD Information
<Enter> ..
Advance DRAM Configuration <Enter> .
DRAM Timing Mode
DRAM SPD( ) EEPROM DRAM. [Auto] SPD BIOSDRAM » DRAM «. [Manual] DRAM » DRAM » .
FSB/DRAM Ratio
FSB/ DRAM .
Adjusted DRAM Frequency (MHz)
. ( ).
HT Link
Control
<Enter> .
46
MS-7641
HT Incoming/
Outgoing Link
Width
. [Auto]HT .
HT Link
Speed
. [Auto]HT .
Adjusted HT Link
Frequency
(MHz)
HT . ( ).
Auto Disable DRAM/PCI Frequency
[Enabled] DRAM/ PCI () (EMI) .
CPU VDD Voltage (V)/ CPU-NB VDD Voltage (V)/ DRAM Voltage (V)
CPU, .
Spread Spectrum
( ). EMI. EMI . EMIEMI ..
*EMI [Disabled]. EMI EMI.
*EMI .EMI .
*.
47
Load Optimized Defaults
다.
48
MS-7641
Français
Pour commencer
Félicitations, vous venez d’aquérir une carte mère Micro-ATX 760GM-P25 (FX)/ 760GM-P23 (FX)/ 760GM-P21 (FX) (MS-7641 v3.x). Les séries 760GM-P25 (FX)/ 760GM-P23 (FX)/ 760GM-P21 (FX) sont basées sur les puces AMD® 760G & SB710 offrant un système très performant. La carte fonctionne avec les processeurs AMD® avancés dans le paquet AM3+, les séries 760GM-P25 (FX)/ 760GMP23 (FX)/ 760GM-P21 (FX) sont très performanantes et offrant une solution adaptée tant aux professionnels qu’aux particuliers.
Schéma
Top : mouse
Bottom:keyboard
Top: VGA Port |
Bottom: DVI-D Port (optional) |
USB2.0 ports
USB2.0 ports
Top: LAN Jack Bottom: USB ports
JUSB_PW1
JPWR2
CPUFAN
DIMM1 DIMM2
T:Line-I n M:Line-O ut B:Mic
T:RS-Ou t
M:CS-Ou t (optional) B:SS-O ut
JCI1
JAUD1
SYSFAN1
AMD 760G
PCI_E1
PCI_E2
AMD SB710
PCI1
JFP2 |
|||
JSP1 |
JCOM1 |
JTPM1 |
|
JUSB_PW2 JUSB1 JUSB2 |
JFP1 |
BUZ1
JPWP1
JBAT1
BATT
+
SATA3 SATA6
49
SPéCIFICATIONS
Processeurs
■ AMD® Phenom II/ Athlon II/ Sempron processeurs dans le paquet AM3+.
(Pour plus d’information sur le CPU, veuillez visiter http://www.msi.com/service/cpu-support/)
HyperTransport
■ HyperTransport™ 3.0, supporte jusqu’à 5.2 GT/s Jeu de puces
■North Bridge : puces AMD® 760G
■South Bridge : puces AMD® SB710
Mémoire
■DDR3 800/ 1066/ 1333 SDRAM (total 16GB Max)
■2 DDR3 DIMMs (240pin / 1.5V)
(Pour plus d’information sur les composants compatibles, veuillez visiter http://www.msi.com/service/test-report/)
LAN
■Supporte LAN 10/100/1000 Fast Ethernet par Realtek® 8111E (760GM-P25 (FX)/ 760GM-P23 (FX))
■Supporte LAN 10/100 Fast Ethernet par Realtek® 8105E (760GM-P21 (FX))
Audio
■Puces intégrées par Realtek® ALC892 (760GM-P25 (FX))
■Puces intégrées par Realtek® ALC887 (760GM-P23 (FX)/ 760GM-P21 (FX))
■Supporte 7.1 canaux audio out
■Conforme aux spécifications Azalia 1.0
SATA
■ 6 ports SATA 3Gb/s par AMD® SB710
RAID
■ SATA 1~6 supportent le mode RAID 0/ 1/ 10 ou JBOD par AMD® SB710 Connecteurs
■Panneau arrière I/O
1 port souris PS/2
1 port clavier PS/2
1 port VGA
1 port DVI-D (760GM-P25 (FX)/ 760GM-P23 (FX))
6 ports USB 2.0
1 prise LAN
6 prises audio flexibles (760GM-P25 (FX))
3 prises audio flexibles (760GM-P23 (FX)/ 760GM-P21 (FX))
■Connecteurs intégrés
2 connecteurs USB 2.0
1 connecteur S/PDIF-Out
1 connecteur audio avant
1 connecteur châssis Intrusion
1 connecteur de port sérial
1 connecteur TPM
50
Loading…
MS-7641
MS-7641
MS-7641
MS-7641
MS-7641
Top : mouse
Bottom:k eyboard
Top: VGA Port
Bottom: DV I-D P ort (optional)
USB2.0 por ts
USB2.0 por ts
2
Top: LAN Jack
JPWP1
JUSB_PW 1
Bottom: US B por ts
JPWR
DIMM1
DIMM2
CPUFAN
T:
Line-I n
M:
Line-O ut
SYSFAN1
B:
Mic
T:RS-Ou t
AMD
M:CS-Ou t
(optiona l)
760G
B:SS-O ut
JCI1
1
AT
PCI_E1
BUZ1
JB
BATT
PCI_E2
+
AMD
4
5
6
SB710
TA
TA
TA
SA
SA
SA
PCI1
JFP2
1
2
3
TA
TA
TA
JAUD1
JSP1
JCOM1
JTPM1
SA
SA
SA
JUSB_PW2
JUSB2JUSB1
JFP1
MS-7641
MS-7641
MS-7641
12 . +3.3
11
10 . +12V
.+ 1 2V
9. 5 VSB
8. P W
V
7
6. + 5V
.G r ound
5
R O
4. + 5
.G r ound
3
K
2. + 3.3
.G r ound
V
1. + 3.3
24 . Grou n d
V
23 . +5
V
22 . +5
21 . +5
20 . Res
V
19 . Grou n d
V
18 . Grou n d
V
17 . Grou n d
16 . PS-O N
15 . Grou n d
14 . —12V
13 . +3.3
#
V
1
2
.G r ound
.G r ound
3. + 12V
4. + 12V
MS-7641
1
2
.
G
3
.
+
r
.
S
1
o
e
2
u
n
V
n
d
s
o
r
1
2
.
G
3
.
r
4
.
+
S
1
o
.
e
2
u
C
V
n
o
n
d
n
s
t
o
r
r
o
l
1
2
.
G
.
3
S
r
.
V
P
o
u
D
n
C
C
I
F
d
P
ow e r
P
S
wi t ch
10 . No
ow e r
LE
Pi
D
8.
n
6.
—
4.
+
2.
—
+
9. R eser v e
7.
5.
+
3.
—
1.
—
+
Re s et
d
HD D
S
wi t ch
LE
D
S
peaker
8.
Buzzer
6.
+
4.
—
2.
+
—
7.No
5.Power
3.Suspend
Pi
1
.Ground
n
LE
D
LE
D
1
0
8
.
.
N
6
C
o
.
T
P
4
D
S
.
S
i
n
2
D
R
.
T
S
R
I
N
9
7
.
R
5
.
R
I
3
.
G
T
1
.
S
r
S
.
D
O
o
u
C
U
n
T
d
D
1
0
8
.
6
.
H
N
e
.
o
a
4
M
.
I
P
d
P
C
i
P
2
n
h
.
G
R
E
D
o
r
n
o
S
e
t
u
E
e
e
n
N
c
D
d
t
i
e
C
o
t
E
n
e
c
#
t
i
o
n
9
7
.
H
5
.
S
e
a
3
.
H
E
d
N
P
1
.
M
e
a
S
.
M
I
C
d
E
h
o
n
I
_
C
R
P
h
S
e
o
E
L
L
n
N
e
D
R
1
0
8
.
.
NC
6
G
r
4
.
U
o
.
S
u
2
U
B
n
.
V
S
1
d
C
B
1
+
C
—
9
7
.
N
5
.
G
o
P
3
.
U
r
o
i
n
1
.
U
S
u
.
S
B
n
V
C
B
0
d
0
+
C
—
MS-7641
1
1
4
.
1
2
G
0
.
G
r
o
8
.
r
u
6
.
N
o
5
o
u
n
d
.
n
4
S
V
e
P
P
i
d
.
o
n
2
3
r
i
w
.
.
a
3
3
V
V
l
I
e
r
S
P
R
Q
t
o
a
w
n
e
d
r
b
y
p
o
w
e
1
r
1
3
1
.
L
9
.
L
P
P
C
7
.
L
5
.
C
F
L
P
C
a
r
.
P
a
3
L
P
C
a
d
m
.
L
a
d
d
d
r
e
1
.
C
e
L
P
P
C
a
d
d
r
e
s
C
s
R
d
d
r
e
s
s
&
C
e
r
e
s
s
&
d
l
s
e
o
s
a
c
t
s
&
d
a
t
k
&
d
a
t
a
a
d
t
p
a
p
i
a
n
t
a
p
i
n
3
i
n
2
p
i
n
1
0
2
1
.
G
.
C
r
o
I
N
u
n
T
d
R
U
1
1
1
1
1
1
1
1
MS-7641
MS-7641
MS-7641
MS-7641
MS-7641
MS-7641
BATT
+
JUSB2JUSB1
JFP1
JFP2
PCI_E1
PCI_E2
PCI1
JPWR
2
JUSB_PW 1
JUSB_PW2
SYSFAN1
CPUFAN
JCI1
JCOM1
JAUD1
JSP1
JB
AT
1
SA
TA
6
SA
TA
3
SA
TA
5
SA
TA
2
SA
TA
4
SA
TA
1
JPWP1
DIMM1
DIMM2
BUZ1
Top: LAN Jack
Bottom: US B por ts
Top: VGA Port
Bottom: DV I-D P ort (optional)
USB2.0 por ts
USB2.0 por ts
JTPM1
T:
M:
B:
Line-I n
Line-O ut
Mic
T:RS-Ou t
M:CS-Ou t
B:SS-O ut
AMD
760G
AMD
SB710
Top : mouse
Bottom:k eyboard
(optiona l)
MS-7641
MS-7641
MS-7641
13 . +3.3
V
1. + 3.3
V
14 . —12V
2. + 3.3
V
15 . Grou n d
3
.G r ound
16 . PS-O N
#
4. + 5
V
17 . Grou n d
5
.G r ound
18 . Grou n d
6. + 5V
19 . Grou n d
7
.G r ound
22 . +5
V
10 . +12V
20 . Res
8. P W
R O
K
23 . +5
V
11
.+ 1 2V
21 . +5
V
9. 5 VSB
24 . Grou n d
12 . +3.3
V
4. + 12V
2
.G r ound
3. + 12V
1
.G r ound
MS-7641
1
.
G
r
o
u
n
d
2
.
+
1
2
V
3
.
S
e
n
s
o
r
4
.
C
o
n
t
r
o
l
1.
+
3.
—
10 . No
Pi
n
5.
—
Re s et
S
wi t ch
HD D
LE
D
P
ow e r
S
wi t ch
P
ow e r
LE
D
7.
+
9. R eser v e
d
8.
—
6.
+
4.
—
2.
+
1
.Ground
3.Suspend
LE
D
5.Power
LE
D
7.No
Pi
n
8.
+
6.
—
4.
+
2.
—
Buzzer
S
peaker
1
.
D
C
D
3
.
S
O
U
T
1
0
.
N
o
P
i
n
5
.
G
r
o
u
n
d
7
.
R
T
S
9
.
R
I
8
.
C
T
S
6
.
D
S
R
4
.
D
T
R
2
.
S
I
N
1
.
M
I
C
L
3
.
M
I
C
R
1
0
.
H
e
a
d
P
h
o
n
e
D
e
t
e
c
t
i
o
n
5
.
H
e
a
d
P
h
o
n
e
R
7
.
S
E
N
S
E
_
S
E
N
D
9
.
H
e
a
d
P
h
o
n
e
L
8
.
N
o
P
i
n
6
.
M
I
C
D
e
t
e
c
t
i
o
n
4
.
P
R
E
S
E
N
C
E
#
2
.
G
r
o
u
n
d
1
.
V
C
C
3
.
U
S
B
0
—
1
0
.
NC
5
.
U
S
B
0
+
7
.
G
r
o
u
n
d
9
.
N
o
P
i
n
8
.
G
r
o
u
n
d
6
.
U
S
B
1
+
4
.
U
S
B
1
—
2
.
V
C
C
MS-7641
1
0
.
N
o
P
i
n
1
4
.
G
r
o
u
n
d
8
.
5
V
P
o
w
e
r
1
2
.
G
r
o
u
n
d
6
.
S
e
r
i
a
l
I
R
Q
4
.
3
.
3
V
P
o
w
e
r
2
.
3
V
S
t
a
n
d
b
y
p
o
w
e
r
1
.
L
P
C
C
l
o
c
k
3
.
L
P
C
R
e
s
e
t
5
.
L
P
C
a
d
d
r
e
s
s
&
d
a
t
a
p
i
n
0
7
.
L
P
C
a
d
d
r
e
s
s
&
d
a
t
a
p
i
n
1
9
.
L
P
C
a
d
d
r
e
s
s
&
d
a
t
a
p
i
n
2
1
1
.
L
P
C
a
d
d
r
e
s
s
&
d
a
t
a
p
i
n
3
1
3
.
L
P
C
F
r
a
m
e
MS-7641
MS-7641
MS-7641
MS-7641
Page 1 —
MS-7641
Page 2
Page 3
Page 4
MS-7641
Page 5
Page 6
MS-7641
Page 7
Page 8
MS-7641
Page 9
Page 10 —
MS-7641
Page 12
MS-7641
Page 13
MS-7641
Page 14
Page 15
MS-7641
Page 16
Page 17
MS-7641
Page 18
Page 19
MS-7641
Page 20
13 . +3.3V1. + 3.3V14 .
Page 21
MS-76411.Gro
Page 22
1.DCD3.SOUT10.No Pin5.Ground7.RTS9.RI8.CTS6.DSR4.DTR2.SIN
Page 23
MS-7641 10.No Pin14.Ground8.5V Power12.Ground6.Serial IRQ4.3.3V Powe
Page 24
Page 25
111
Page 26
MS-7641
Page 27
Page 28
MS-7641
Page 29
Page 30
MS-7641
Page 31
Page 32
MS-7641
Page 33
Page 34
Page 35
MS-7641
Page 36
Page 37
Page 38
Page 39
Page 40
Page 41
Page 42
13 . +3.3V1. + 3.3V14 . -12V2. + 3.3V15 . Grou n
Page 43
1
Page 44
1.DCD3.SOUT10.No Pin5.Ground7.RTS9.RI8.CTS6.DSR4.DTR2.SIN
Page 45
10.No Pin14.Ground8.5V Power12.Ground6.Serial IRQ4.3.3V Power2.3V Standby power1.LPC Clock3.LP
Page 46
Page 47
111
Page 48
Page 49
Page 50
Page 51
Page 52
Page 53
Page 54
Page 55
Page 56
MS-7641
Page 57
MS-7641
Page 58
Page 59
MS-7641
Page 60
Page 61
MS-7641
Page 62
Page 63
MS-7641
Page 64
13 . +3.3V1. + 3.3V14 . -12V2. + 3.3V
Page 65
MS-7641
Page 66
1.DCD3.SOUT10.No Pin5.Ground7.RTS9.RI8.CTS6.DSR4.DTR2.S
Page 67
MS-764110.No Pin14.Ground8.5V Power12.Gr
Page 68
Page 69
111
Page 70
MS-7641
Page 71
Page 72
MS-7641
Page 73
Page 74
MS-7641
Page 75
Page 76
MS-7641
Page 77
Page 78
Page 79
MS-7641
Page 80
Page 81
MS-7641
Page 82
Page 83
Page 84
MS-7641
Page 85
Page 86
MS-7641
Page 87
Page 88
MS-7641
Page 89
Page 90
MS-7641
Page 91
Page 92
MS-7641
Page 93
MS-7641
Page 94
Page 95
MS-7641
Page 96
Page 97
MS-7641
Page 98
Page 99
MS-7641
Page 100 —
Page 101
MS-7641
Page 102 —
1.DCD3.SOUT10.No Pin5.Ground7.RTS9.RI8.CTS6.DSR4.DTR2.SIN
Page 103
MS-764110.No Pin14.Ground8.5V Power12.Ground6.Ser
Page 104
Page 105
111
Page 106
MS-7641
Page 107
Page 108
MS-7641
Page 109 — USB2.0 por ts
Page 110 —
MS-7641
Page 111
Page 112
MS-7641
Page 113
Page 114
MS-7641
Page 115
MS-7641
Page 116
Page 117
MS-7641
Page 118
Page 119
MS-7641
Page 120
Page 121
MS-7641
Page 122
Page 123
MS-7641
Page 124
Page 125
MS-7641
Page 126
Page 127
Page 128
MS-7641
Page 129
Page 130
MS-7641
Page 131
Page 132
MS-7641
Page 133
Page 134
MS-7641
Page 135
Page 136
MS-7641
Page 137
MS-7641
Page 138
Page 140
Page 141
MS-7641
Page 142
Page 143
MS-7641
Page 144
Page 145
MS-7641
Page 146
Page 147
MS-7641
Page 148
Page 149
Page 150
MS-7641
Page 151
Page 152
MS-7641
Page 153
Page 154
MS-7641
Page 155
Page 156
MS-7641
Page 157
Page 158
MS-7641
Page 159
MS-7641
Page 160
Page 161
MS-7641
Page 162
Page 163
MS-7641
Page 164
Page 165
MS-7641
Page 166
Page 167
MS-7641
Page 168
Page 169
MS-7641